aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--Documentation/filesystems/squashfs.txt2
-rw-r--r--Documentation/ftrace.txt2
-rw-r--r--arch/arm/mach-at91/at91sam9263_devices.c105
-rw-r--r--arch/arm/mach-at91/include/mach/board.h3
-rw-r--r--arch/blackfin/Kconfig7
-rw-r--r--arch/blackfin/Kconfig.debug6
-rw-r--r--arch/blackfin/configs/BF518F-EZBRD_defconfig63
-rw-r--r--arch/blackfin/configs/BF527-EZKIT_defconfig4
-rw-r--r--arch/blackfin/configs/BF533-EZKIT_defconfig4
-rw-r--r--arch/blackfin/configs/BF533-STAMP_defconfig4
-rw-r--r--arch/blackfin/configs/BF537-STAMP_defconfig14
-rw-r--r--arch/blackfin/configs/BF538-EZKIT_defconfig4
-rw-r--r--arch/blackfin/configs/BF548-EZKIT_defconfig6
-rw-r--r--arch/blackfin/configs/BF561-EZKIT_defconfig4
-rw-r--r--arch/blackfin/configs/BlackStamp_defconfig4
-rw-r--r--arch/blackfin/configs/CM-BF527_defconfig4
-rw-r--r--arch/blackfin/configs/CM-BF548_defconfig6
-rw-r--r--arch/blackfin/configs/IP0X_defconfig2
-rw-r--r--arch/blackfin/configs/SRV1_defconfig4
-rw-r--r--arch/blackfin/include/asm/Kbuild1
-rw-r--r--arch/blackfin/include/asm/bfin_sport.h45
-rw-r--r--arch/blackfin/include/asm/ipipe.h100
-rw-r--r--arch/blackfin/include/asm/ipipe_base.h12
-rw-r--r--arch/blackfin/include/asm/irq.h36
-rw-r--r--arch/blackfin/include/asm/thread_info.h2
-rw-r--r--arch/blackfin/kernel/Makefile8
-rw-r--r--arch/blackfin/kernel/cplb-nompu/cplbinit.c4
-rw-r--r--arch/blackfin/kernel/ipipe.c176
-rw-r--r--arch/blackfin/kernel/irqchip.c14
-rw-r--r--arch/blackfin/kernel/kgdb_test.c9
-rw-r--r--arch/blackfin/kernel/ptrace.c5
-rw-r--r--arch/blackfin/kernel/setup.c10
-rw-r--r--arch/blackfin/kernel/time.c5
-rw-r--r--arch/blackfin/mach-bf518/boards/ezbrd.c33
-rw-r--r--arch/blackfin/mach-bf518/include/mach/anomaly.h17
-rw-r--r--arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h4
-rw-r--r--arch/blackfin/mach-bf527/boards/cm_bf527.c26
-rw-r--r--arch/blackfin/mach-bf527/boards/ezbrd.c24
-rw-r--r--arch/blackfin/mach-bf527/include/mach/anomaly.h6
-rw-r--r--arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h4
-rw-r--r--arch/blackfin/mach-bf533/boards/Kconfig5
-rw-r--r--arch/blackfin/mach-bf533/boards/Makefile1
-rw-r--r--arch/blackfin/mach-bf533/boards/blackstamp.c24
-rw-r--r--arch/blackfin/mach-bf533/boards/cm_bf533.c24
-rw-r--r--arch/blackfin/mach-bf533/boards/generic_board.c126
-rw-r--r--arch/blackfin/mach-bf533/boards/ip0x.c13
-rw-r--r--arch/blackfin/mach-bf533/include/mach/anomaly.h7
-rw-r--r--arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h2
-rw-r--r--arch/blackfin/mach-bf537/boards/Kconfig5
-rw-r--r--arch/blackfin/mach-bf537/boards/Makefile1
-rw-r--r--arch/blackfin/mach-bf537/boards/cm_bf537.c26
-rw-r--r--arch/blackfin/mach-bf537/boards/generic_board.c745
-rw-r--r--arch/blackfin/mach-bf537/boards/minotaur.c24
-rw-r--r--arch/blackfin/mach-bf537/boards/pnav10.c24
-rw-r--r--arch/blackfin/mach-bf537/boards/tcm_bf537.c24
-rw-r--r--arch/blackfin/mach-bf537/include/mach/anomaly.h7
-rw-r--r--arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h4
-rw-r--r--arch/blackfin/mach-bf538/include/mach/anomaly.h6
-rw-r--r--arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h4
-rw-r--r--arch/blackfin/mach-bf548/include/mach/anomaly.h22
-rw-r--r--arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h22
-rw-r--r--arch/blackfin/mach-bf548/include/mach/irq.h8
-rw-r--r--arch/blackfin/mach-bf561/boards/Kconfig5
-rw-r--r--arch/blackfin/mach-bf561/boards/Makefile1
-rw-r--r--arch/blackfin/mach-bf561/boards/cm_bf561.c15
-rw-r--r--arch/blackfin/mach-bf561/boards/generic_board.c113
-rw-r--r--arch/blackfin/mach-bf561/include/mach/anomaly.h7
-rw-r--r--arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h2
-rw-r--r--arch/blackfin/mach-common/arch_checks.c9
-rw-r--r--arch/blackfin/mach-common/cache.S22
-rw-r--r--arch/blackfin/mach-common/clocks-init.c2
-rw-r--r--arch/blackfin/mach-common/dpmc_modes.S24
-rw-r--r--arch/blackfin/mach-common/entry.S61
-rw-r--r--arch/blackfin/mach-common/interrupt.S12
-rw-r--r--arch/blackfin/mach-common/ints-priority.c126
-rw-r--r--arch/blackfin/mach-common/smp.c6
-rw-r--r--arch/blackfin/mm/init.c2
-rw-r--r--arch/ia64/sn/pci/pcibr/pcibr_dma.c7
-rw-r--r--arch/mips/include/asm/compat.h7
-rw-r--r--arch/x86/kernel/ds.c3
-rw-r--r--block/blk-merge.c25
-rw-r--r--drivers/ata/ahci.c24
-rw-r--r--drivers/ata/libata-core.c14
-rw-r--r--drivers/ata/libata-eh.c7
-rw-r--r--drivers/ata/sata_nv.c2
-rw-r--r--drivers/block/cciss.c8
-rw-r--r--drivers/block/loop.c3
-rw-r--r--drivers/block/xen-blkfront.c2
-rw-r--r--drivers/dca/dca-core.c2
-rw-r--r--drivers/dma/dmatest.c6
-rw-r--r--drivers/dma/fsldma.c8
-rw-r--r--drivers/dma/ioat.c2
-rw-r--r--drivers/dma/ioat_dca.c26
-rw-r--r--drivers/dma/ioat_dma.c39
-rw-r--r--drivers/dma/ioatdma.h8
-rw-r--r--drivers/dma/ioatdma_hw.h2
-rw-r--r--drivers/dma/ioatdma_registers.h2
-rw-r--r--drivers/dma/iop-adma.c16
-rw-r--r--drivers/dma/ipu/ipu_idmac.c2
-rw-r--r--drivers/dma/mv_xor.c16
-rw-r--r--drivers/ide/Kconfig5
-rw-r--r--drivers/ide/Makefile1
-rw-r--r--drivers/ide/at91_ide.c467
-rw-r--r--drivers/ide/ide-disk_proc.c2
-rw-r--r--drivers/ide/ide-floppy_proc.c2
-rw-r--r--drivers/ide/ide-io.c3
-rw-r--r--drivers/ide/ide-iops.c2
-rw-r--r--drivers/ide/ide-probe.c7
-rw-r--r--drivers/ide/ide-proc.c2
-rw-r--r--drivers/ide/ide-tape.c2
-rw-r--r--drivers/mmc/core/mmc_ops.c15
-rw-r--r--drivers/watchdog/gef_wdt.c2
-rw-r--r--drivers/watchdog/ks8695_wdt.c1
-rw-r--r--drivers/watchdog/orion5x_wdt.c1
-rw-r--r--drivers/watchdog/rc32434_wdt.c168
-rw-r--r--fs/ext4/ialloc.c8
-rw-r--r--fs/squashfs/block.c13
-rw-r--r--fs/squashfs/cache.c4
-rw-r--r--fs/squashfs/inode.c6
-rw-r--r--fs/squashfs/squashfs.h2
-rw-r--r--fs/squashfs/super.c2
-rw-r--r--include/asm-generic/vmlinux.lds.h2
-rw-r--r--include/linux/ata.h2
-rw-r--r--include/linux/dmaengine.h7
-rw-r--r--include/linux/hdreg.h1
-rw-r--r--include/linux/ide.h1
-rw-r--r--include/linux/kernel.h10
-rw-r--r--include/linux/libata.h6
-rw-r--r--include/linux/serio.h2
-rw-r--r--kernel/softirq.c1
-rw-r--r--security/smack/smack_lsm.c43
-rw-r--r--security/smack/smackfs.c64
-rw-r--r--sound/pci/hda/patch_sigmatel.c6
133 files changed, 1526 insertions, 1885 deletions
diff --git a/Documentation/filesystems/squashfs.txt b/Documentation/filesystems/squashfs.txt
index 3e79e4a7a39..b324c033035 100644
--- a/Documentation/filesystems/squashfs.txt
+++ b/Documentation/filesystems/squashfs.txt
@@ -22,7 +22,7 @@ Squashfs filesystem features versus Cramfs:
Squashfs Cramfs
-Max filesystem size: 2^64 16 MiB
+Max filesystem size: 2^64 256 MiB
Max file size: ~ 2 TiB 16 MiB
Max files: unlimited unlimited
Max directories: unlimited unlimited
diff --git a/Documentation/ftrace.txt b/Documentation/ftrace.txt
index 22614bef635..fd9a3e69381 100644
--- a/Documentation/ftrace.txt
+++ b/Documentation/ftrace.txt
@@ -100,7 +100,7 @@ of ftrace. Here is a list of some of the key files:
that is displayed in one of the above output
files.
- trace_max_latency:
+ tracing_max_latency:
Some of the tracers record the max latency.
For example, the time interrupts are disabled.
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 134af97ff34..b7f23324231 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -347,6 +347,111 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
#endif
+/* --------------------------------------------------------------------
+ * Compact Flash (PCMCIA or IDE)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) || \
+ defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
+
+static struct at91_cf_data cf0_data;
+
+static struct resource cf0_resources[] = {
+ [0] = {
+ .start = AT91_CHIPSELECT_4,
+ .end = AT91_CHIPSELECT_4 + SZ_256M - 1,
+ .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+ }
+};
+
+static struct platform_device cf0_device = {
+ .id = 0,
+ .dev = {
+ .platform_data = &cf0_data,
+ },
+ .resource = cf0_resources,
+ .num_resources = ARRAY_SIZE(cf0_resources),
+};
+
+static struct at91_cf_data cf1_data;
+
+static struct resource cf1_resources[] = {
+ [0] = {
+ .start = AT91_CHIPSELECT_5,
+ .end = AT91_CHIPSELECT_5 + SZ_256M - 1,
+ .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+ }
+};
+
+static struct platform_device cf1_device = {
+ .id = 1,
+ .dev = {
+ .platform_data = &cf1_data,
+ },
+ .resource = cf1_resources,
+ .num_resources = ARRAY_SIZE(cf1_resources),
+};
+
+void __init at91_add_device_cf(struct at91_cf_data *data)
+{
+ unsigned long ebi0_csa;
+ struct platform_device *pdev;
+
+ if (!data)
+ return;
+
+ /*
+ * assign CS4 or CS5 to SMC with Compact Flash logic support,
+ * we assume SMC timings are configured by board code,
+ * except True IDE where timings are controlled by driver
+ */
+ ebi0_csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+ switch (data->chipselect) {
+ case 4:
+ at91_set_A_periph(AT91_PIN_PD6, 0); /* EBI0_NCS4/CFCS0 */
+ ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
+ cf0_data = *data;
+ pdev = &cf0_device;
+ break;
+ case 5:
+ at91_set_A_periph(AT91_PIN_PD7, 0); /* EBI0_NCS5/CFCS1 */
+ ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
+ cf1_data = *data;
+ pdev = &cf1_device;
+ break;
+ default:
+ printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
+ data->chipselect);
+ return;
+ }
+ at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
+
+ if (data->det_pin) {
+ at91_set_gpio_input(data->det_pin, 1);
+ at91_set_deglitch(data->det_pin, 1);
+ }
+
+ if (data->irq_pin) {
+ at91_set_gpio_input(data->irq_pin, 1);
+ at91_set_deglitch(data->irq_pin, 1);
+ }
+
+ if (data->vcc_pin)
+ /* initially off */
+ at91_set_gpio_output(data->vcc_pin, 0);
+
+ /* enable EBI controlled pins */
+ at91_set_A_periph(AT91_PIN_PD5, 1); /* NWAIT */
+ at91_set_A_periph(AT91_PIN_PD8, 0); /* CFCE1 */
+ at91_set_A_periph(AT91_PIN_PD9, 0); /* CFCE2 */
+ at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
+
+ pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "at91_ide" : "at91_cf";
+ platform_device_register(pdev);
+}
+#else
+void __init at91_add_device_cf(struct at91_cf_data *data) {}
+#endif
/* --------------------------------------------------------------------
* NAND / SmartMedia
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 0b3ae21b456..793fe7b25f3 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -56,6 +56,9 @@ struct at91_cf_data {
u8 vcc_pin; /* power switching */
u8 rst_pin; /* card reset */
u8 chipselect; /* EBI Chip Select number */
+ u8 flags;
+#define AT91_CF_TRUE_IDE 0x01
+#define AT91_IDE_SWAP_A0_A2 0x02
};
extern void __init at91_add_device_cf(struct at91_cf_data *data);
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 8f1f97d56e1..0c1f86e3e44 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -1129,6 +1129,7 @@ endchoice
config PM_WAKEUP_BY_GPIO
bool "Allow Wakeup from Standby by GPIO"
+ depends on PM && !BF54x
config PM_WAKEUP_GPIO_NUMBER
int "GPIO number"
@@ -1168,6 +1169,12 @@ config PM_BFIN_WAKE_GP
default n
help
Enable General-Purpose Wake-Up (Voltage Regulator Power-Up)
+ (all processors, except ADSP-BF549). This option sets
+ the general-purpose wake-up enable (GPWE) control bit to enable
+ wake-up upon detection of an active low signal on the /GPW (PH7) pin.
+ On ADSP-BF549 this option enables the the same functionality on the
+ /MRXON pin also PH7.
+
endmenu
menu "CPU Frequency scaling"
diff --git a/arch/blackfin/Kconfig.debug b/arch/blackfin/Kconfig.debug
index 5f981d9ca62..79e7e63ab70 100644
--- a/arch/blackfin/Kconfig.debug
+++ b/arch/blackfin/Kconfig.debug
@@ -21,12 +21,6 @@ config DEBUG_STACK_USAGE
config HAVE_ARCH_KGDB
def_bool y
-config KGDB_TESTCASE
- tristate "KGDB: for test case in expect"
- default n
- help
- This is a kgdb test case for automated testing.
-
config DEBUG_VERBOSE
bool "Verbose fault messages"
default y
diff --git a/arch/blackfin/configs/BF518F-EZBRD_defconfig b/arch/blackfin/configs/BF518F-EZBRD_defconfig
index 4fdb9e04759..281f4b60e60 100644
--- a/arch/blackfin/configs/BF518F-EZBRD_defconfig
+++ b/arch/blackfin/configs/BF518F-EZBRD_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc2
-# Fri Jan 9 17:58:41 2009
+# Linux kernel version: 2.6.28
+# Fri Feb 20 10:01:44 2009
#
# CONFIG_MMU is not set
# CONFIG_FPU is not set
@@ -133,10 +133,15 @@ CONFIG_BF518=y
# CONFIG_BF538 is not set
# CONFIG_BF539 is not set
# CONFIG_BF542 is not set
+# CONFIG_BF542M is not set
# CONFIG_BF544 is not set
+# CONFIG_BF544M is not set
# CONFIG_BF547 is not set
+# CONFIG_BF547M is not set
# CONFIG_BF548 is not set
+# CONFIG_BF548M is not set
# CONFIG_BF549 is not set
+# CONFIG_BF549M is not set
# CONFIG_BF561 is not set
CONFIG_BF_REV_MIN=0
CONFIG_BF_REV_MAX=2
@@ -426,7 +431,17 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
-# CONFIG_NET_DSA is not set
+CONFIG_NET_DSA=y
+# CONFIG_NET_DSA_TAG_DSA is not set
+# CONFIG_NET_DSA_TAG_EDSA is not set
+# CONFIG_NET_DSA_TAG_TRAILER is not set
+CONFIG_NET_DSA_TAG_STPID=y
+# CONFIG_NET_DSA_MV88E6XXX is not set
+# CONFIG_NET_DSA_MV88E6060 is not set
+# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
+# CONFIG_NET_DSA_MV88E6131 is not set
+# CONFIG_NET_DSA_MV88E6123_61_65 is not set
+CONFIG_NET_DSA_KSZ8893M=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
@@ -529,6 +544,8 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
#
# Self-contained MTD device drivers
#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
@@ -561,7 +578,9 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_HD is not set
CONFIG_MISC_DEVICES=y
# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_C2PORT is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
@@ -607,6 +626,7 @@ CONFIG_BFIN_RX_DESC_NUM=20
# CONFIG_SMC91X is not set
# CONFIG_SMSC911X is not set
# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
# CONFIG_IBM_NEW_EMAC_ZMII is not set
# CONFIG_IBM_NEW_EMAC_RGMII is not set
# CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -764,7 +784,23 @@ CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
-# CONFIG_SPI is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BFIN=y
+# CONFIG_SPI_BFIN_LOCK is not set
+# CONFIG_SPI_BITBANG is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not set
@@ -788,8 +824,10 @@ CONFIG_BFIN_WDT=y
# CONFIG_MFD_SM501 is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
+# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
#
# Multimedia devices
@@ -861,10 +899,18 @@ CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_DRV_M41T80 is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
#
# Platform RTC drivers
@@ -1062,12 +1108,20 @@ CONFIG_DEBUG_INFO=y
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
+
+#
+# Tracers
+#
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_KGDB_TESTCASE is not set
CONFIG_DEBUG_VERBOSE=y
CONFIG_DEBUG_MMRS=y
# CONFIG_DEBUG_HWERR is not set
@@ -1100,6 +1154,7 @@ CONFIG_CRYPTO=y
#
# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_CRYPTD is not set
diff --git a/arch/blackfin/configs/BF527-EZKIT_defconfig b/arch/blackfin/configs/BF527-EZKIT_defconfig
index 833128b3972..a50050f1770 100644
--- a/arch/blackfin/configs/BF527-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF527-EZKIT_defconfig
@@ -327,8 +327,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/BF533-EZKIT_defconfig b/arch/blackfin/configs/BF533-EZKIT_defconfig
index 334c94b51c4..0a2a00d6388 100644
--- a/arch/blackfin/configs/BF533-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF533-EZKIT_defconfig
@@ -290,8 +290,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/BF533-STAMP_defconfig b/arch/blackfin/configs/BF533-STAMP_defconfig
index 9d733436e30..eb027587a35 100644
--- a/arch/blackfin/configs/BF533-STAMP_defconfig
+++ b/arch/blackfin/configs/BF533-STAMP_defconfig
@@ -290,8 +290,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/BF537-STAMP_defconfig b/arch/blackfin/configs/BF537-STAMP_defconfig
index 4fb4108d310..9e62b9f40eb 100644
--- a/arch/blackfin/configs/BF537-STAMP_defconfig
+++ b/arch/blackfin/configs/BF537-STAMP_defconfig
@@ -298,8 +298,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
@@ -568,15 +568,7 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
-CONFIG_MTD_NAND=m
-# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-# CONFIG_MTD_NAND_ECC_SMC is not set
-# CONFIG_MTD_NAND_MUSEUM_IDS is not set
-# CONFIG_MTD_NAND_BFIN is not set
-CONFIG_MTD_NAND_IDS=m
-# CONFIG_MTD_NAND_DISKONCHIP is not set
-# CONFIG_MTD_NAND_NANDSIM is not set
-CONFIG_MTD_NAND_PLATFORM=m
+# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
#
diff --git a/arch/blackfin/configs/BF538-EZKIT_defconfig b/arch/blackfin/configs/BF538-EZKIT_defconfig
index cb32f5624a1..dd6ad6be1c8 100644
--- a/arch/blackfin/configs/BF538-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF538-EZKIT_defconfig
@@ -306,8 +306,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/BF548-EZKIT_defconfig b/arch/blackfin/configs/BF548-EZKIT_defconfig
index 0f8697618aa..6bc2fb1b2a7 100644
--- a/arch/blackfin/configs/BF548-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF548-EZKIT_defconfig
@@ -361,8 +361,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_BFIN_L2_CACHEABLE is not set
# CONFIG_MPU is not set
@@ -680,7 +680,7 @@ CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/BF561-EZKIT_defconfig b/arch/blackfin/configs/BF561-EZKIT_defconfig
index 042c7adfccf..69714fb3e60 100644
--- a/arch/blackfin/configs/BF561-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF561-EZKIT_defconfig
@@ -329,8 +329,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_BFIN_L2_CACHEABLE is not set
# CONFIG_MPU is not set
diff --git a/arch/blackfin/configs/BlackStamp_defconfig b/arch/blackfin/configs/BlackStamp_defconfig
index 3a20e281d23..017c6ea071b 100644
--- a/arch/blackfin/configs/BlackStamp_defconfig
+++ b/arch/blackfin/configs/BlackStamp_defconfig
@@ -288,8 +288,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/CM-BF527_defconfig b/arch/blackfin/configs/CM-BF527_defconfig
index 865ed85a576..d880ef78677 100644
--- a/arch/blackfin/configs/CM-BF527_defconfig
+++ b/arch/blackfin/configs/CM-BF527_defconfig
@@ -332,8 +332,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
# CONFIG_MPU is not set
#
diff --git a/arch/blackfin/configs/CM-BF548_defconfig b/arch/blackfin/configs/CM-BF548_defconfig
index efe9741b1f1..f410430b4e3 100644
--- a/arch/blackfin/configs/CM-BF548_defconfig
+++ b/arch/blackfin/configs/CM-BF548_defconfig
@@ -336,8 +336,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
CONFIG_L1_MAX_PIECE=16
# CONFIG_MPU is not set
@@ -595,7 +595,7 @@ CONFIG_SCSI=y
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/IP0X_defconfig b/arch/blackfin/configs/IP0X_defconfig
index eae83b5de92..7db93874c98 100644
--- a/arch/blackfin/configs/IP0X_defconfig
+++ b/arch/blackfin/configs/IP0X_defconfig
@@ -612,7 +612,7 @@ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_SCSI=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/SRV1_defconfig b/arch/blackfin/configs/SRV1_defconfig
index fa580affc9d..a46529c6ade 100644
--- a/arch/blackfin/configs/SRV1_defconfig
+++ b/arch/blackfin/configs/SRV1_defconfig
@@ -282,8 +282,8 @@ CONFIG_BFIN_ICACHE=y
CONFIG_BFIN_DCACHE=y
# CONFIG_BFIN_DCACHE_BANKA is not set
# CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
-CONFIG_BFIN_WT=y
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
CONFIG_L1_MAX_PIECE=16
#
diff --git a/arch/blackfin/include/asm/Kbuild b/arch/blackfin/include/asm/Kbuild
index 606ecfdcc96..09c31418cc0 100644
--- a/arch/blackfin/include/asm/Kbuild
+++ b/arch/blackfin/include/asm/Kbuild
@@ -1,3 +1,4 @@
include include/asm-generic/Kbuild.asm
+unifdef-y += bfin_sport.h
unifdef-y += fixed_code.h
diff --git a/arch/blackfin/include/asm/bfin_sport.h b/arch/blackfin/include/asm/bfin_sport.h
index fe88a2c1921..65a651db5b0 100644
--- a/arch/blackfin/include/asm/bfin_sport.h
+++ b/arch/blackfin/include/asm/bfin_sport.h
@@ -1,30 +1,9 @@
/*
- * File: include/asm-blackfin/bfin_sport.h
- * Based on:
- * Author: Roy Huang (roy.huang@analog.com)
+ * bfin_sport.h - userspace header for bfin sport driver
*
- * Created: Thu Aug. 24 2006
- * Description:
+ * Copyright 2004-2008 Analog Devices Inc.
*
- * Modified:
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * Licensed under the GPL-2 or later.
*/
#ifndef __BFIN_SPORT_H__
@@ -42,11 +21,10 @@
#define NORM_FORMAT 0x0
#define ALAW_FORMAT 0x2
#define ULAW_FORMAT 0x3
-struct sport_register;
/* Function driver which use sport must initialize the structure */
struct sport_config {
- /*TDM (multichannels), I2S or other mode */
+ /* TDM (multichannels), I2S or other mode */
unsigned int mode:3;
/* if TDM mode is selected, channels must be set */
@@ -72,12 +50,18 @@ struct sport_config {
int serial_clk;
int fsync_clk;
- unsigned int data_format:2; /*Normal, u-law or a-law */
+ unsigned int data_format:2; /* Normal, u-law or a-law */
int word_len; /* How length of the word in bits, 3-32 bits */
int dma_enabled;
};
+/* Userspace interface */
+#define SPORT_IOC_MAGIC 'P'
+#define SPORT_IOC_CONFIG _IOWR('P', 0x01, struct sport_config)
+
+#ifdef __KERNEL__
+
struct sport_register {
unsigned short tcr1;
unsigned short reserved0;
@@ -117,9 +101,6 @@ struct sport_register {
unsigned long mrcs3;
};
-#define SPORT_IOC_MAGIC 'P'
-#define SPORT_IOC_CONFIG _IOWR('P', 0x01, struct sport_config)
-
struct sport_dev {
struct cdev cdev; /* Char device structure */
@@ -149,6 +130,8 @@ struct sport_dev {
struct sport_config config;
};
+#endif
+
#define SPORT_TCR1 0
#define SPORT_TCR2 1
#define SPORT_TCLKDIV 2
@@ -169,4 +152,4 @@ struct sport_dev {
#define SPORT_MRCS2 22
#define SPORT_MRCS3 23
-#endif /*__BFIN_SPORT_H__*/
+#endif
diff --git a/arch/blackfin/include/asm/ipipe.h b/arch/blackfin/include/asm/ipipe.h
index 76f53d8b9a0..343b56361ec 100644
--- a/arch/blackfin/include/asm/ipipe.h
+++ b/arch/blackfin/include/asm/ipipe.h
@@ -35,9 +35,9 @@
#include <asm/atomic.h>
#include <asm/traps.h>
-#define IPIPE_ARCH_STRING "1.8-00"
+#define IPIPE_ARCH_STRING "1.9-00"
#define IPIPE_MAJOR_NUMBER 1
-#define IPIPE_MINOR_NUMBER 8
+#define IPIPE_MINOR_NUMBER 9
#define IPIPE_PATCH_NUMBER 0
#ifdef CONFIG_SMP
@@ -83,9 +83,9 @@ struct ipipe_sysinfo {
"%2 = CYCLES2\n" \
"CC = %2 == %0\n" \
"if ! CC jump 1b\n" \
- : "=r" (((unsigned long *)&t)[1]), \
- "=r" (((unsigned long *)&t)[0]), \
- "=r" (__cy2) \
+ : "=d,a" (((unsigned long *)&t)[1]), \
+ "=d,a" (((unsigned long *)&t)[0]), \
+ "=d,a" (__cy2) \
: /*no input*/ : "CC"); \
t; \
})
@@ -118,35 +118,40 @@ void __ipipe_disable_irqdesc(struct ipipe_domain *ipd,
#define __ipipe_disable_irq(irq) (irq_desc[irq].chip->mask(irq))
-#define __ipipe_lock_root() \
- set_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags)
+static inline int __ipipe_check_tickdev(const char *devname)
+{
+ return 1;
+}
-#define __ipipe_unlock_root() \
- clear_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags)
+static inline void __ipipe_lock_root(void)
+{
+ set_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status));
+}
+
+static inline void __ipipe_unlock_root(void)
+{
+ clear_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status));
+}
void __ipipe_enable_pipeline(void);
#define __ipipe_hook_critical_ipi(ipd) do { } while (0)
-#define __ipipe_sync_pipeline(syncmask) \
- do { \
- struct ipipe_domain *ipd = ipipe_current_domain; \
- if (likely(ipd != ipipe_root_domain || !test_bit(IPIPE_ROOTLOCK_FLAG, &ipd->flags))) \
- __ipipe_sync_stage(syncmask); \
- } while (0)
+#define __ipipe_sync_pipeline ___ipipe_sync_pipeline
+void ___ipipe_sync_pipeline(unsigned long syncmask);
void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs);
int __ipipe_get_irq_priority(unsigned irq);
-int __ipipe_get_irqthread_priority(unsigned irq);
-
void __ipipe_stall_root_raw(void);
void __ipipe_unstall_root_raw(void);
void __ipipe_serial_debug(const char *fmt, ...);
+asmlinkage void __ipipe_call_irqtail(unsigned long addr);
+
DECLARE_PER_CPU(struct pt_regs, __ipipe_tick_regs);
extern unsigned long __ipipe_core_clock;
@@ -162,42 +167,25 @@ static inline unsigned long __ipipe_ffnz(unsigned long ul)
#define __ipipe_run_irqtail() /* Must be a macro */ \
do { \
- asmlinkage void __ipipe_call_irqtail(void); \
unsigned long __pending; \
- CSYNC(); \
+ CSYNC(); \
__pending = bfin_read_IPEND(); \
if (__pending & 0x8000) { \
__pending &= ~0x8010; \
if (__pending && (__pending & (__pending - 1)) == 0) \
- __ipipe_call_irqtail(); \
+ __ipipe_call_irqtail(__ipipe_irq_tail_hook); \
} \
} while (0)
#define __ipipe_run_isr(ipd, irq) \
do { \
if (ipd == ipipe_root_domain) { \
- /* \
- * Note: the I-pipe implements a threaded interrupt model on \
- * this arch for Linux external IRQs. The interrupt handler we \
- * call here only wakes up the associated IRQ thread. \
- */ \
- if (ipipe_virtual_irq_p(irq)) { \
- /* No irqtail here; virtual interrupts have no effect \
- on IPEND so there is no need for processing \
- deferral. */ \
- local_irq_enable_nohead(ipd); \
+ local_irq_enable_hw(); \
+ if (ipipe_virtual_irq_p(irq)) \
ipd->irqs[irq].handler(irq, ipd->irqs[irq].cookie); \
- local_irq_disable_nohead(ipd); \
- } else \
- /* \
- * No need to run the irqtail here either; \
- * we can't be preempted by hw IRQs, so \
- * non-Linux IRQs cannot stack over the short \
- * thread wakeup code. Which in turn means \
- * that no irqtail condition could be pending \
- * for domains above Linux in the pipeline. \
- */ \
+ else \
ipd->irqs[irq].handler(irq, &__raw_get_cpu_var(__ipipe_tick_regs)); \
+ local_irq_disable_hw(); \
} else { \
__clear_bit(IPIPE_SYNC_FLAG, &ipipe_cpudom_var(ipd, status)); \
local_irq_enable_nohead(ipd); \
@@ -217,42 +205,24 @@ void ipipe_init_irq_threads(void);
int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc);
-#define IS_SYSIRQ(irq) ((irq) > IRQ_CORETMR && (irq) <= SYS_IRQS)
-#define IS_GPIOIRQ(irq) ((irq) >= GPIO_IRQ_BASE && (irq) < NR_IRQS)
-
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+#define IRQ_SYSTMR IRQ_CORETMR
+#define IRQ_PRIOTMR IRQ_CORETMR
+#else
#define IRQ_SYSTMR IRQ_TIMER0
#define IRQ_PRIOTMR CONFIG_IRQ_TIMER0
+#endif
-#if defined(CONFIG_BF531) || defined(CONFIG_BF532) || defined(CONFIG_BF533)
-#define PRIO_GPIODEMUX(irq) CONFIG_PFA
-#elif defined(CONFIG_BF534) || defined(CONFIG_BF536) || defined(CONFIG_BF537)
-#define PRIO_GPIODEMUX(irq) CONFIG_IRQ_PROG_INTA
-#elif defined(CONFIG_BF52x)
-#define PRIO_GPIODEMUX(irq) ((irq) == IRQ_PORTF_INTA ? CONFIG_IRQ_PORTF_INTA : \
- (irq) == IRQ_PORTG_INTA ? CONFIG_IRQ_PORTG_INTA : \
- (irq) == IRQ_PORTH_INTA ? CONFIG_IRQ_PORTH_INTA : \
- -1)
-#elif defined(CONFIG_BF561)
-#define PRIO_GPIODEMUX(irq) ((irq) == IRQ_PROG0_INTA ? CONFIG_IRQ_PROG0_INTA : \
- (irq) == IRQ_PROG1_INTA ? CONFIG_IRQ_PROG1_INTA : \
- (irq) == IRQ_PROG2_INTA ? CONFIG_IRQ_PROG2_INTA : \
- -1)
+#ifdef CONFIG_BF561
#define bfin_write_TIMER_DISABLE(val) bfin_write_TMRS8_DISABLE(val)
#define bfin_write_TIMER_ENABLE(val) bfin_write_TMRS8_ENABLE(val)
#define bfin_write_TIMER_STATUS(val) bfin_write_TMRS8_STATUS(val)
#define bfin_read_TIMER_STATUS() bfin_read_TMRS8_STATUS()
#elif defined(CONFIG_BF54x)
-#define PRIO_GPIODEMUX(irq) ((irq) == IRQ_PINT0 ? CONFIG_IRQ_PINT0 : \
- (irq) == IRQ_PINT1 ? CONFIG_IRQ_PINT1 : \
- (irq) == IRQ_PINT2 ? CONFIG_IRQ_PINT2 : \
- (irq) == IRQ_PINT3 ? CONFIG_IRQ_PINT3 : \
- -1)
#define bfin_write_TIMER_DISABLE(val) bfin_write_TIMER_DISABLE0(val)
#define bfin_write_TIMER_ENABLE(val) bfin_write_TIMER_ENABLE0(val)
#define bfin_write_TIMER_STATUS(val) bfin_write_TIMER_STATUS0(val)
#define bfin_read_TIMER_STATUS(val) bfin_read_TIMER_STATUS0(val)
-#else
-# error "no PRIO_GPIODEMUX() for this part"
#endif
#define __ipipe_root_tick_p(regs) ((regs->ipend & 0x10) != 0)
@@ -275,4 +245,6 @@ int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc);
#endif /* !CONFIG_IPIPE */
+#define ipipe_update_tick_evtdev(evtdev) do { } while (0)
+
#endif /* !__ASM_BLACKFIN_IPIPE_H */
diff --git a/arch/blackfin/include/asm/ipipe_base.h b/arch/blackfin/include/asm/ipipe_base.h
index cb1025aeabc..3e8acbd1a3b 100644
--- a/arch/blackfin/include/asm/ipipe_base.h
+++ b/arch/blackfin/include/asm/ipipe_base.h
@@ -1,5 +1,5 @@
/* -*- linux-c -*-
- * include/asm-blackfin/_baseipipe.h
+ * include/asm-blackfin/ipipe_base.h
*
* Copyright (C) 2007 Philippe Gerum.
*
@@ -27,8 +27,9 @@
#define IPIPE_NR_XIRQS NR_IRQS
#define IPIPE_IRQ_ISHIFT 5 /* 2^5 for 32bits arch. */
-/* Blackfin-specific, global domain flags */
-#define IPIPE_ROOTLOCK_FLAG 1 /* Lock pipeline for root */
+/* Blackfin-specific, per-cpu pipeline status */
+#define IPIPE_SYNCDEFER_FLAG 15
+#define IPIPE_SYNCDEFER_MASK (1L << IPIPE_SYNCDEFER_MASK)
/* Blackfin traps -- i.e. exception vector numbers */
#define IPIPE_NR_FAULTS 52 /* We leave a gap after VEC_ILL_RES. */
@@ -48,11 +49,6 @@
#ifndef __ASSEMBLY__
-#include <linux/bitops.h>
-
-extern int test_bit(int nr, const void *addr);
-
-
extern unsigned long __ipipe_root_status; /* Alias to ipipe_root_cpudom_var(status) */
static inline void __ipipe_stall_root(void)
diff --git a/arch/blackfin/include/asm/irq.h b/arch/blackfin/include/asm/irq.h
index 3d977909ce7..7645e85a5f6 100644
--- a/arch/blackfin/include/asm/irq.h
+++ b/arch/blackfin/include/asm/irq.h
@@ -61,20 +61,38 @@ void __ipipe_restore_root(unsigned long flags);
#define raw_irqs_disabled_flags(flags) (!irqs_enabled_from_flags_hw(flags))
#define local_test_iflag_hw(x) irqs_enabled_from_flags_hw(x)
-#define local_save_flags(x) \
- do { \
- (x) = __ipipe_test_root() ? \
+#define local_save_flags(x) \
+ do { \
+ (x) = __ipipe_test_root() ? \
__all_masked_irq_flags : bfin_irq_flags; \
+ barrier(); \
} while (0)
-#define local_irq_save(x) \
- do { \
- (x) = __ipipe_test_and_stall_root(); \
+#define local_irq_save(x) \
+ do { \
+ (x) = __ipipe_test_and_stall_root() ? \
+ __all_masked_irq_flags : bfin_irq_flags; \
+ barrier(); \
+ } while (0)
+
+static inline void local_irq_restore(unsigned long x)
+{
+ barrier();
+ __ipipe_restore_root(x == __all_masked_irq_flags);
+}
+
+#define local_irq_disable() \
+ do { \
+ __ipipe_stall_root(); \
+ barrier(); \
} while (0)
-#define local_irq_restore(x) __ipipe_restore_root(x)
-#define local_irq_disable() __ipipe_stall_root()
-#define local_irq_enable() __ipipe_unstall_root()
+static inline void local_irq_enable(void)
+{
+ barrier();
+ __ipipe_unstall_root();
+}
+
#define irqs_disabled() __ipipe_test_root()
#define local_save_flags_hw(x) \
diff --git a/arch/blackfin/include/asm/thread_info.h b/arch/blackfin/include/asm/thread_info.h
index e721ce55956..2920087516f 100644
--- a/arch/blackfin/include/asm/thread_info.h
+++ b/arch/blackfin/include/asm/thread_info.h
@@ -122,6 +122,7 @@ static inline struct thread_info *current_thread_info(void)
#define TIF_MEMDIE 4
#define TIF_RESTORE_SIGMASK 5 /* restore signal mask in do_signal() */
#define TIF_FREEZE 6 /* is freezing for suspend */
+#define TIF_IRQ_SYNC 7 /* sync pipeline stage */
/* as above, but as bit values */
#define _TIF_SYSCALL_TRACE (1<<TIF_SYSCALL_TRACE)
@@ -130,6 +131,7 @@ static inline struct thread_info *current_thread_info(void)
#define _TIF_POLLING_NRFLAG (1<<TIF_POLLING_NRFLAG)
#define _TIF_RESTORE_SIGMASK (1<<TIF_RESTORE_SIGMASK)
#define _TIF_FREEZE (1<<TIF_FREEZE)
+#define _TIF_IRQ_SYNC (1<<TIF_IRQ_SYNC)
#define _TIF_WORK_MASK 0x0000FFFE /* work to do on interrupt/exception return */
diff --git a/arch/blackfin/kernel/Makefile b/arch/blackfin/kernel/Makefile
index 4a92a86824b..fd4d4328a0f 100644
--- a/arch/blackfin/kernel/Makefile
+++ b/arch/blackfin/kernel/Makefile
@@ -15,13 +15,15 @@ else
obj-y += time.o
endif
-CFLAGS_kgdb_test.o := -mlong-calls -O0
-
obj-$(CONFIG_IPIPE) += ipipe.o
obj-$(CONFIG_IPIPE_TRACE_MCOUNT) += mcount.o
obj-$(CONFIG_BFIN_GPTIMERS) += gptimers.o
obj-$(CONFIG_CPLB_INFO) += cplbinfo.o
obj-$(CONFIG_MODULES) += module.o
obj-$(CONFIG_KGDB) += kgdb.o
-obj-$(CONFIG_KGDB_TESTCASE) += kgdb_test.o
+obj-$(CONFIG_KGDB_TESTS) += kgdb_test.o
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
+
+# the kgdb test puts code into L2 and without linker
+# relaxation, we need to force long calls to/from it
+CFLAGS_kgdb_test.o := -mlong-calls -O0
diff --git a/arch/blackfin/kernel/cplb-nompu/cplbinit.c b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
index 0e28f759573..d6c067782e6 100644
--- a/arch/blackfin/kernel/cplb-nompu/cplbinit.c
+++ b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
@@ -53,9 +53,13 @@ void __init generate_cplb_tables_cpu(unsigned int cpu)
i_d = i_i = 0;
+#ifdef CONFIG_DEBUG_HUNT_FOR_ZERO
/* Set up the zero page. */
d_tbl[i_d].addr = 0;
d_tbl[i_d++].data = SDRAM_OOPS | PAGE_SIZE_1KB;
+ i_tbl[i_i].addr = 0;
+ i_tbl[i_i++].data = SDRAM_OOPS | PAGE_SIZE_1KB;
+#endif
/* Cover kernel memory with 4M pages. */
addr = 0;
diff --git a/arch/blackfin/kernel/ipipe.c b/arch/blackfin/kernel/ipipe.c
index 339be5a3ae6..a5de8d45424 100644
--- a/arch/blackfin/kernel/ipipe.c
+++ b/arch/blackfin/kernel/ipipe.c
@@ -35,14 +35,8 @@
#include <asm/atomic.h>
#include <asm/io.h>
-static int create_irq_threads;
-
DEFINE_PER_CPU(struct pt_regs, __ipipe_tick_regs);
-static DEFINE_PER_CPU(unsigned long, pending_irqthread_mask);
-
-static DEFINE_PER_CPU(int [IVG13 + 1], pending_irq_count);
-
asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs);
static void __ipipe_no_irqtail(void);
@@ -93,6 +87,7 @@ void __ipipe_enable_pipeline(void)
*/
void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
{
+ struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr();
struct ipipe_domain *this_domain, *next_domain;
struct list_head *head, *pos;
int m_ack, s = -1;
@@ -104,7 +99,6 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
* interrupt.
*/
m_ack = (regs == NULL || irq == IRQ_SYSTMR || irq == IRQ_CORETMR);
-
this_domain = ipipe_current_domain;
if (unlikely(test_bit(IPIPE_STICKY_FLAG, &this_domain->irqs[irq].control)))
@@ -114,49 +108,28 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
next_domain = list_entry(head, struct ipipe_domain, p_link);
if (likely(test_bit(IPIPE_WIRED_FLAG, &next_domain->irqs[irq].control))) {
if (!m_ack && next_domain->irqs[irq].acknowledge != NULL)
- next_domain->irqs[irq].acknowledge(irq, irq_desc + irq);
- if (test_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags))
- s = __test_and_set_bit(IPIPE_STALL_FLAG,
- &ipipe_root_cpudom_var(status));
+ next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
+ if (test_bit(IPIPE_SYNCDEFER_FLAG, &p->status))
+ s = __test_and_set_bit(IPIPE_STALL_FLAG, &p->status);
__ipipe_dispatch_wired(next_domain, irq);
- goto finalize;
- return;
+ goto out;
}
}
/* Ack the interrupt. */
pos = head;
-
while (pos != &__ipipe_pipeline) {
next_domain = list_entry(pos, struct ipipe_domain, p_link);
- /*
- * For each domain handling the incoming IRQ, mark it
- * as pending in its log.
- */
if (test_bit(IPIPE_HANDLE_FLAG, &next_domain->irqs[irq].control)) {
- /*
- * Domains that handle this IRQ are polled for
- * acknowledging it by decreasing priority
- * order. The interrupt must be made pending
- * _first_ in the domain's status flags before
- * the PIC is unlocked.
- */
__ipipe_set_irq_pending(next_domain, irq);
-
if (!m_ack && next_domain->irqs[irq].acknowledge != NULL) {
- next_domain->irqs[irq].acknowledge(irq, irq_desc + irq);
+ next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
m_ack = 1;
}
}
-
- /*
- * If the domain does not want the IRQ to be passed
- * down the interrupt pipe, exit the loop now.
- */
if (!test_bit(IPIPE_PASS_FLAG, &next_domain->irqs[irq].control))
break;
-
pos = next_domain->p_link.next;
}
@@ -166,18 +139,24 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
* immediately to the current domain if the interrupt has been
* marked as 'sticky'. This search does not go beyond the
* current domain in the pipeline. We also enforce the
- * additional root stage lock (blackfin-specific). */
+ * additional root stage lock (blackfin-specific).
+ */
+ if (test_bit(IPIPE_SYNCDEFER_FLAG, &p->status))
+ s = __test_and_set_bit(IPIPE_STALL_FLAG, &p->status);
- if (test_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags))
- s = __test_and_set_bit(IPIPE_STALL_FLAG,
- &ipipe_root_cpudom_var(status));
-finalize:
+ /*
+ * If the interrupt preempted the head domain, then do not
+ * even try to walk the pipeline, unless an interrupt is
+ * pending for it.
+ */
+ if (test_bit(IPIPE_AHEAD_FLAG, &this_domain->flags) &&
+ ipipe_head_cpudom_var(irqpend_himask) == 0)
+ goto out;
__ipipe_walk_pipeline(head);
-
+out:
if (!s)
- __clear_bit(IPIPE_STALL_FLAG,
- &ipipe_root_cpudom_var(status));
+ __clear_bit(IPIPE_STALL_FLAG, &p->status);
}
int __ipipe_check_root(void)
@@ -187,7 +166,7 @@ int __ipipe_check_root(void)
void __ipipe_enable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
{
- struct irq_desc *desc = irq_desc + irq;
+ struct irq_desc *desc = irq_to_desc(irq);
int prio = desc->ic_prio;
desc->depth = 0;
@@ -199,7 +178,7 @@ EXPORT_SYMBOL(__ipipe_enable_irqdesc);
void __ipipe_disable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
{
- struct irq_desc *desc = irq_desc + irq;
+ struct irq_desc *desc = irq_to_desc(irq);
int prio = desc->ic_prio;
if (ipd != &ipipe_root &&
@@ -236,15 +215,18 @@ int __ipipe_syscall_root(struct pt_regs *regs)
{
unsigned long flags;
- /* We need to run the IRQ tail hook whenever we don't
+ /*
+ * We need to run the IRQ tail hook whenever we don't
* propagate a syscall to higher domains, because we know that
* important operations might be pending there (e.g. Xenomai
- * deferred rescheduling). */
+ * deferred rescheduling).
+ */
- if (!__ipipe_syscall_watched_p(current, regs->orig_p0)) {
+ if (regs->orig_p0 < NR_syscalls) {
void (*hook)(void) = (void (*)(void))__ipipe_irq_tail_hook;
hook();
- return 0;
+ if ((current->flags & PF_EVNOTIFY) == 0)
+ return 0;
}
/*
@@ -312,112 +294,46 @@ int ipipe_trigger_irq(unsigned irq)
{
unsigned long flags;
+#ifdef CONFIG_IPIPE_DEBUG
if (irq >= IPIPE_NR_IRQS ||
(ipipe_virtual_irq_p(irq)
&& !test_bit(irq - IPIPE_VIRQ_BASE, &__ipipe_virtual_irq_map)))
return -EINVAL;
+#endif
local_irq_save_hw(flags);
-
__ipipe_handle_irq(irq, NULL);
-
local_irq_restore_hw(flags);
return 1;
}
-/* Move Linux IRQ to threads. */
-
-static int do_irqd(void *__desc)
+asmlinkage void __ipipe_sync_root(void)
{
- struct irq_desc *desc = __desc;
- unsigned irq = desc - irq_desc;
- int thrprio = desc->thr_prio;
- int thrmask = 1 << thrprio;
- int cpu = smp_processor_id();
- cpumask_t cpumask;
-
- sigfillset(&current->blocked);
- current->flags |= PF_NOFREEZE;
- cpumask = cpumask_of_cpu(cpu);
- set_cpus_allowed(current, cpumask);
- ipipe_setscheduler_root(current, SCHED_FIFO, 50 + thrprio);
-
- while (!kthread_should_stop()) {
- local_irq_disable();
- if (!(desc->status & IRQ_SCHEDULED)) {
- set_current_state(TASK_INTERRUPTIBLE);
-resched:
- local_irq_enable();
- schedule();
- local_irq_disable();
- }
- __set_current_state(TASK_RUNNING);
- /*
- * If higher priority interrupt servers are ready to
- * run, reschedule immediately. We need this for the
- * GPIO demux IRQ handler to unmask the interrupt line
- * _last_, after all GPIO IRQs have run.
- */
- if (per_cpu(pending_irqthread_mask, cpu) & ~(thrmask|(thrmask-1)))
- goto resched;
- if (--per_cpu(pending_irq_count[thrprio], cpu) == 0)
- per_cpu(pending_irqthread_mask, cpu) &= ~thrmask;
- desc->status &= ~IRQ_SCHEDULED;
- desc->thr_handler(irq, &__raw_get_cpu_var(__ipipe_tick_regs));
- local_irq_enable();
- }
- __set_current_state(TASK_RUNNING);
- return 0;
-}
+ unsigned long flags;
-static void kick_irqd(unsigned irq, void *cookie)
-{
- struct irq_desc *desc = irq_desc + irq;
- int thrprio = desc->thr_prio;
- int thrmask = 1 << thrprio;
- int cpu = smp_processor_id();
-
- if (!(desc->status & IRQ_SCHEDULED)) {
- desc->status |= IRQ_SCHEDULED;
- per_cpu(pending_irqthread_mask, cpu) |= thrmask;
- ++per_cpu(pending_irq_count[thrprio], cpu);
- wake_up_process(desc->thread);
- }
-}
+ BUG_ON(irqs_disabled());
-int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc)
-{
- if (desc->thread || !create_irq_threads)
- return 0;
-
- desc->thread = kthread_create(do_irqd, desc, "IRQ %d", irq);
- if (desc->thread == NULL) {
- printk(KERN_ERR "irqd: could not create IRQ thread %d!\n", irq);
- return -ENOMEM;
- }
+ local_irq_save_hw(flags);
- wake_up_process(desc->thread);
+ clear_thread_flag(TIF_IRQ_SYNC);
- desc->thr_handler = ipipe_root_domain->irqs[irq].handler;
- ipipe_root_domain->irqs[irq].handler = &kick_irqd;
+ if (ipipe_root_cpudom_var(irqpend_himask) != 0)
+ __ipipe_sync_pipeline(IPIPE_IRQMASK_ANY);
- return 0;
+ local_irq_restore_hw(flags);
}
-void __init ipipe_init_irq_threads(void)
+void ___ipipe_sync_pipeline(unsigned long syncmask)
{
- unsigned irq;
- struct irq_desc *desc;
-
- create_irq_threads = 1;
+ struct ipipe_domain *ipd = ipipe_current_domain;
- for (irq = 0; irq < NR_IRQS; irq++) {
- desc = irq_desc + irq;
- if (desc->action != NULL ||
- (desc->status & IRQ_NOREQUEST) != 0)
- ipipe_start_irq_thread(irq, desc);
+ if (ipd == ipipe_root_domain) {
+ if (test_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status)))
+ return;
}
+
+ __ipipe_sync_stage(syncmask);
}
EXPORT_SYMBOL(show_stack);
diff --git a/arch/blackfin/kernel/irqchip.c b/arch/blackfin/kernel/irqchip.c
index 23e9aa08071..1ab5b532ec7 100644
--- a/arch/blackfin/kernel/irqchip.c
+++ b/arch/blackfin/kernel/irqchip.c
@@ -149,11 +149,15 @@ asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
#endif
generic_handle_irq(irq);
-#ifndef CONFIG_IPIPE /* Useless and bugous over the I-pipe: IRQs are threaded. */
- /* If we're the only interrupt running (ignoring IRQ15 which is for
- syscalls), lower our priority to IRQ14 so that softirqs run at
- that level. If there's another, lower-level interrupt, irq_exit
- will defer softirqs to that. */
+#ifndef CONFIG_IPIPE
+ /*
+ * If we're the only interrupt running (ignoring IRQ15 which
+ * is for syscalls), lower our priority to IRQ14 so that
+ * softirqs run at that level. If there's another,
+ * lower-level interrupt, irq_exit will defer softirqs to
+ * that. If the interrupt pipeline is enabled, we are already
+ * running at IRQ14 priority, so we don't need this code.
+ */
CSYNC();
pending = bfin_read_IPEND() & ~0x8000;
other_ints = pending & (pending - 1);
diff --git a/arch/blackfin/kernel/kgdb_test.c b/arch/blackfin/kernel/kgdb_test.c
index 3dba9c17304..dbcf3e45cb0 100644
--- a/arch/blackfin/kernel/kgdb_test.c
+++ b/arch/blackfin/kernel/kgdb_test.c
@@ -20,6 +20,7 @@
static char cmdline[256];
static unsigned long len;
+#ifndef CONFIG_SMP
static int num1 __attribute__((l1_data));
void kgdb_l1_test(void) __attribute__((l1_text));
@@ -32,6 +33,8 @@ void kgdb_l1_test(void)
printk(KERN_ALERT "L1(after change) : data variable addr = 0x%p, data value is %d\n", &num1, num1);
return ;
}
+#endif
+
#if L2_LENGTH
static int num2 __attribute__((l2));
@@ -59,10 +62,12 @@ int kgdb_test(char *name, int len, int count, int z)
static int test_proc_output(char *buf)
{
kgdb_test("hello world!", 12, 0x55, 0x10);
+#ifndef CONFIG_SMP
kgdb_l1_test();
- #if L2_LENGTH
+#endif
+#if L2_LENGTH
kgdb_l2_test();
- #endif
+#endif
return 0;
}
diff --git a/arch/blackfin/kernel/ptrace.c b/arch/blackfin/kernel/ptrace.c
index 594e325b40e..d76618db50d 100644
--- a/arch/blackfin/kernel/ptrace.c
+++ b/arch/blackfin/kernel/ptrace.c
@@ -45,6 +45,7 @@
#include <asm/asm-offsets.h>
#include <asm/dma.h>
#include <asm/fixed_code.h>
+#include <asm/cacheflush.h>
#include <asm/mem_map.h>
#define TEXT_OFFSET 0
@@ -240,7 +241,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
} else if (addr >= FIXED_CODE_START
&& addr + sizeof(tmp) <= FIXED_CODE_END) {
- memcpy(&tmp, (const void *)(addr), sizeof(tmp));
+ copy_from_user_page(0, 0, 0, &tmp, (const void *)(addr), sizeof(tmp));
copied = sizeof(tmp);
} else
@@ -320,7 +321,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
} else if (addr >= FIXED_CODE_START
&& addr + sizeof(data) <= FIXED_CODE_END) {
- memcpy((void *)(addr), &data, sizeof(data));
+ copy_to_user_page(0, 0, 0, (void *)(addr), &data, sizeof(data));
copied = sizeof(data);
} else
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index e5c11623080..a58687bdee6 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -889,6 +889,10 @@ void __init setup_arch(char **cmdline_p)
CPU, bfin_revid());
}
+ /* We can't run on BF548-0.1 due to ANOMALY 05000448 */
+ if (bfin_cpuid() == 0x27de && bfin_revid() == 1)
+ panic("You can't run on this processor due to 05000448\n");
+
printk(KERN_INFO "Blackfin Linux support by http://blackfin.uclinux.org/\n");
printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu MHz System Clock\n",
@@ -1141,12 +1145,12 @@ static int show_cpuinfo(struct seq_file *m, void *v)
icache_size = 0;
seq_printf(m, "cache size\t: %d KB(L1 icache) "
- "%d KB(L1 dcache-%s) %d KB(L2 cache)\n",
+ "%d KB(L1 dcache%s) %d KB(L2 cache)\n",
icache_size, dcache_size,
#if defined CONFIG_BFIN_WB
- "wb"
+ "-wb"
#elif defined CONFIG_BFIN_WT
- "wt"
+ "-wt"
#endif
"", 0);
diff --git a/arch/blackfin/kernel/time.c b/arch/blackfin/kernel/time.c
index 172b4c58846..1bbacfbd4c5 100644
--- a/arch/blackfin/kernel/time.c
+++ b/arch/blackfin/kernel/time.c
@@ -134,7 +134,10 @@ irqreturn_t timer_interrupt(int irq, void *dummy)
write_seqlock(&xtime_lock);
#if defined(CONFIG_TICK_SOURCE_SYSTMR0) && !defined(CONFIG_IPIPE)
-/* FIXME: Here TIMIL0 is not set when IPIPE enabled, why? */
+ /*
+ * TIMIL0 is latched in __ipipe_grab_irq() when the I-Pipe is
+ * enabled.
+ */
if (get_gptimer_status(0) & TIMER_STATUS_TIMIL0) {
#endif
do_timer(1);
diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 0e175342112..41f2eacfef2 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -113,7 +113,6 @@ static struct platform_device bfin_mac_device = {
.name = "bfin_mac",
.dev.platform_data = &bfin_mii_bus,
};
-#endif
#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
static struct dsa_platform_data ksz8893m_switch_data = {
@@ -132,6 +131,7 @@ static struct platform_device ksz8893m_switch_device = {
.dev.platform_data = &ksz8893m_switch_data,
};
#endif
+#endif
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -171,6 +171,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
#if defined(CONFIG_NET_DSA_KSZ8893M) \
|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
/* SPI SWITCH CHIP */
@@ -179,10 +180,11 @@ static struct bfin5xx_spi_chip spi_switch_info = {
.bits_per_word = 8,
};
#endif
+#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -259,6 +261,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
#if defined(CONFIG_NET_DSA_KSZ8893M) \
|| defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
{
@@ -271,24 +274,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.mode = SPI_MODE_3,
},
#endif
+#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc_dummy",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "spi_mmc",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
@@ -630,11 +624,10 @@ static struct platform_device *stamp_devices[] __initdata = {
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
&bfin_mii_bus,
&bfin_mac_device,
-#endif
-
#if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
&ksz8893m_switch_device,
#endif
+#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&bfin_spi0_device,
diff --git a/arch/blackfin/mach-bf518/include/mach/anomaly.h b/arch/blackfin/mach-bf518/include/mach/anomaly.h
index e5b4bef0eda..c847bb10107 100644
--- a/arch/blackfin/mach-bf518/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf518/include/mach/anomaly.h
@@ -2,12 +2,12 @@
* File: include/asm-blackfin/mach-bf518/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
/* This file shoule be up to date with:
- * - ????
+ * - Revision B, 02/03/2009; ADSP-BF512/BF514/BF516/BF518 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
@@ -19,6 +19,8 @@
#define ANOMALY_05000122 (1)
/* False Hardware Error from an Access in the Shadow of a Conditional Branch */
#define ANOMALY_05000245 (1)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (1)
/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
#define ANOMALY_05000265 (1)
/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
@@ -53,6 +55,12 @@
#define ANOMALY_05000443 (1)
/* Incorrect L1 Instruction Bank B Memory Map Location */
#define ANOMALY_05000444 (1)
+/* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */
+#define ANOMALY_05000452 (1)
+/* PWM_TRIPB Signal Not Available on PG10 */
+#define ANOMALY_05000453 (1)
+/* PPI_FS3 is Driven One Half Cycle Later Than PPI Data */
+#define ANOMALY_05000455 (1)
/* Anomalies that don't exist on this proc */
#define ANOMALY_05000125 (0)
@@ -65,15 +73,20 @@
#define ANOMALY_05000263 (0)
#define ANOMALY_05000266 (0)
#define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
#define ANOMALY_05000285 (0)
+#define ANOMALY_05000305 (0)
#define ANOMALY_05000307 (0)
#define ANOMALY_05000311 (0)
#define ANOMALY_05000312 (0)
#define ANOMALY_05000323 (0)
#define ANOMALY_05000353 (0)
#define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
#define ANOMALY_05000386 (0)
#define ANOMALY_05000412 (0)
#define ANOMALY_05000432 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
index b50a63b975a..e21c1c3e4ec 100644
--- a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART1_TX,
CH_UART1_RX,
#endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART1_CTS_PIN,
CONFIG_UART1_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 856c097b531..48e69eecdba 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -487,9 +487,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -585,23 +585,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad9960_spi_chip_info,
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "spi_mmc",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .modalias = "mmc_spi",
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 83606fcdde2..7fe480e4ebe 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -256,9 +256,9 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -366,23 +366,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc_dummy",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "spi_mmc",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf527/include/mach/anomaly.h b/arch/blackfin/mach-bf527/include/mach/anomaly.h
index 035e8d83505..df6808d8a6e 100644
--- a/arch/blackfin/mach-bf527/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf527/include/mach/anomaly.h
@@ -2,7 +2,7 @@
* File: include/asm-blackfin/mach-bf527/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
@@ -167,12 +167,16 @@
#define ANOMALY_05000263 (0)
#define ANOMALY_05000266 (0)
#define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
#define ANOMALY_05000285 (0)
+#define ANOMALY_05000305 (0)
#define ANOMALY_05000307 (0)
#define ANOMALY_05000311 (0)
#define ANOMALY_05000312 (0)
#define ANOMALY_05000323 (0)
#define ANOMALY_05000363 (0)
#define ANOMALY_05000412 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
index 75722d6008b..e8c41fd842b 100644
--- a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART1_TX,
CH_UART1_RX,
#endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART1_CTS_PIN,
CONFIG_UART1_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-bf533/boards/Kconfig b/arch/blackfin/mach-bf533/boards/Kconfig
index 308c98dc5ab..8d8b3e7321e 100644
--- a/arch/blackfin/mach-bf533/boards/Kconfig
+++ b/arch/blackfin/mach-bf533/boards/Kconfig
@@ -38,9 +38,4 @@ config BFIN532_IP0X
help
Core support for IP04/IP04 open hardware IP-PBX.
-config GENERIC_BF533_BOARD
- bool "Generic"
- help
- Generic or Custom board support.
-
endchoice
diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile
index 9afbe72b484..ff1e832f80d 100644
--- a/arch/blackfin/mach-bf533/boards/Makefile
+++ b/arch/blackfin/mach-bf533/boards/Makefile
@@ -2,7 +2,6 @@
# arch/blackfin/mach-bf533/boards/Makefile
#
-obj-$(CONFIG_GENERIC_BF533_BOARD) += generic_board.o
obj-$(CONFIG_BFIN533_STAMP) += stamp.o
obj-$(CONFIG_BFIN532_IP0X) += ip0x.o
obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o
diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c
index 015c18f85e7..0765872a8ad 100644
--- a/arch/blackfin/mach-bf533/boards/blackstamp.c
+++ b/arch/blackfin/mach-bf533/boards/blackstamp.c
@@ -101,9 +101,9 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -129,23 +129,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index e7061c7e8c4..e8974878d8c 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -96,9 +96,9 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -138,23 +138,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf533/boards/generic_board.c b/arch/blackfin/mach-bf533/boards/generic_board.c
deleted file mode 100644
index 986eeec53b1..00000000000
--- a/arch/blackfin/mach-bf533/boards/generic_board.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * File: arch/blackfin/mach-bf533/generic_board.c
- * Based on: arch/blackfin/mach-bf533/ezkit.c
- * Author: Aidan Williams <aidan@nicta.com.au>
- *
- * Created: 2005
- * Description:
- *
- * Modified:
- * Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "UNKNOWN BOARD";
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
- .name = "rtc-bfin",
- .id = -1,
-};
-#endif
-
-/*
- * Driver needs to know address, irq and flag pin.
- */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
- {
- .start = 0x20300300,
- .end = 0x20300300 + 16,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PROG_INTB,
- .end = IRQ_PROG_INTB,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- }, {
- .start = IRQ_PF7,
- .end = IRQ_PF7,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir0_device = {
- .name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir0_resources),
- .resource = bfin_sir0_resources,
-};
-#endif
-#endif
-
-static struct platform_device *generic_board_devices[] __initdata = {
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
- &rtc_device,
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
- &smc91x_device,
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
- &bfin_sir0_device,
-#endif
-#endif
-};
-
-static int __init generic_board_init(void)
-{
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- return platform_add_devices(generic_board_devices, ARRAY_SIZE(generic_board_devices));
-}
-
-arch_initcall(generic_board_init);
diff --git a/arch/blackfin/mach-bf533/boards/ip0x.c b/arch/blackfin/mach-bf533/boards/ip0x.c
index e30b1b7d144..f19b63378b1 100644
--- a/arch/blackfin/mach-bf533/boards/ip0x.c
+++ b/arch/blackfin/mach-bf533/boards/ip0x.c
@@ -127,8 +127,8 @@ static struct platform_device dm9000_device2 = {
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* all SPI peripherals info goes here */
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
/*
* CPOL (Clock Polarity)
* 0 - Active high SCK
@@ -152,14 +152,13 @@ static struct bfin5xx_spi_chip spi_mmc_chip_info = {
/* Notice: for blackfin, the speed_hz is the value of register
* SPI_BAUD, not the real baudrate */
static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 2,
.bus_num = 1,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
},
#endif
};
diff --git a/arch/blackfin/mach-bf533/include/mach/anomaly.h b/arch/blackfin/mach-bf533/include/mach/anomaly.h
index 0d3a03429fb..1cf893e2e55 100644
--- a/arch/blackfin/mach-bf533/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf533/include/mach/anomaly.h
@@ -2,7 +2,7 @@
* File: include/asm-blackfin/mach-bf533/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
@@ -160,7 +160,7 @@
#define ANOMALY_05000301 (__SILICON_REVISION__ < 6)
/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
#define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
#define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
@@ -278,9 +278,12 @@
#define ANOMALY_05000266 (0)
#define ANOMALY_05000323 (0)
#define ANOMALY_05000353 (1)
+#define ANOMALY_05000380 (0)
#define ANOMALY_05000386 (1)
#define ANOMALY_05000412 (0)
#define ANOMALY_05000432 (0)
#define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
index f3d9e495230..5f517f53b0f 100644
--- a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
@@ -134,7 +134,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART_TX,
CH_UART_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig
index 42a57b0acb2..77c59da87e8 100644
--- a/arch/blackfin/mach-bf537/boards/Kconfig
+++ b/arch/blackfin/mach-bf537/boards/Kconfig
@@ -33,9 +33,4 @@ config CAMSIG_MINOTAUR
help
Board supply package for CSP Minotaur
-config GENERIC_BF537_BOARD
- bool "Generic"
- help
- Generic or Custom board support.
-
endchoice
diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile
index 7168cc14afd..68b98a7af6a 100644
--- a/arch/blackfin/mach-bf537/boards/Makefile
+++ b/arch/blackfin/mach-bf537/boards/Makefile
@@ -2,7 +2,6 @@
# arch/blackfin/mach-bf537/boards/Makefile
#
-obj-$(CONFIG_GENERIC_BF537_BOARD) += generic_board.o
obj-$(CONFIG_BFIN537_STAMP) += stamp.o
obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o
obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM) += tcm_bf537.o
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 9cd8fb2a30d..41c75b9bfac 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -108,9 +108,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -160,23 +160,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 7,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .modalias = "mmc_spi",
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 1,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c
deleted file mode 100644
index da710fdc456..00000000000
--- a/arch/blackfin/mach-bf537/boards/generic_board.c
+++ /dev/null
@@ -1,745 +0,0 @@
-/*
- * File: arch/blackfin/mach-bf537/boards/generic_board.c
- * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
- * Author: Aidan Williams <aidan@nicta.com.au>
- *
- * Created:
- * Description:
- *
- * Modified:
- * Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2008 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/device.h>
-#include <linux/etherdevice.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/usb/sl811.h>
-#include <asm/dma.h>
-#include <asm/bfin5xx_spi.h>
-#include <asm/reboot.h>
-#include <asm/portmux.h>
-#include <linux/spi/ad7877.h>
-
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "UNKNOWN BOARD";
-
-/*
- * Driver needs to know address, irq and flag pin.
- */
-
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
-#include <linux/usb/isp1760.h>
-static struct resource bfin_isp1760_resources[] = {
- [0] = {
- .start = 0x203C0000,
- .end = 0x203C0000 + 0x000fffff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_PF7,
- .end = IRQ_PF7,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct isp1760_platform_data isp1760_priv = {
- .is_isp1761 = 0,
- .port1_disable = 0,
- .bus_width_16 = 1,
- .port1_otg = 0,
- .analog_oc = 0,
- .dack_polarity_high = 0,
- .dreq_polarity_high = 0,
-};
-
-static struct platform_device bfin_isp1760_device = {
- .name = "isp1760-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1760_priv,
- },
- .num_resources = ARRAY_SIZE(bfin_isp1760_resources),
- .resource = bfin_isp1760_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
-static struct resource bfin_pcmcia_cf_resources[] = {
- {
- .start = 0x20310000, /* IO PORT */
- .end = 0x20312000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20311000, /* Attribute Memory */
- .end = 0x20311FFF,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PF4,
- .end = IRQ_PF4,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- }, {
- .start = 6, /* Card Detect PF6 */
- .end = 6,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bfin_pcmcia_cf_device = {
- .name = "bfin_cf_pcmcia",
- .id = -1,
- .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
- .resource = bfin_pcmcia_cf_resources,
-};
-#endif
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
- .name = "rtc-bfin",
- .id = -1,
-};
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
- {
- .name = "smc91x-regs",
- .start = 0x20300300,
- .end = 0x20300300 + 16,
- .flags = IORESOURCE_MEM,
- }, {
-
- .start = IRQ_PF7,
- .end = IRQ_PF7,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-#endif
-
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
-static struct resource dm9000_resources[] = {
- [0] = {
- .start = 0x203FB800,
- .end = 0x203FB800 + 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = 0x203FB800 + 4,
- .end = 0x203FB800 + 5,
- .flags = IORESOURCE_MEM,
- },
- [2] = {
- .start = IRQ_PF9,
- .end = IRQ_PF9,
- .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
- },
-};
-
-static struct platform_device dm9000_device = {
- .name = "dm9000",
- .id = -1,
- .num_resources = ARRAY_SIZE(dm9000_resources),
- .resource = dm9000_resources,
-};
-#endif
-
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
- {
- .start = 0x20340000,
- .end = 0x20340000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20340004,
- .end = 0x20340004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_SL811_BFIN_IRQ,
- .end = CONFIG_USB_SL811_BFIN_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
- gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
- gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-
-}
-#endif
-
-static struct sl811_platform_data sl811_priv = {
- .potpg = 10,
- .power = 250, /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
- .port_power = &sl811_port_power,
-#endif
-};
-
-static struct platform_device sl811_hcd_device = {
- .name = "sl811-hcd",
- .id = 0,
- .dev = {
- .platform_data = &sl811_priv,
- },
- .num_resources = ARRAY_SIZE(sl811_hcd_resources),
- .resource = sl811_hcd_resources,
-};
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20360000,
- .end = 0x20360000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20360004,
- .end = 0x20360004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-static struct platform_device bfin_mii_bus = {
- .name = "bfin_mii_bus",
-};
-
-static struct platform_device bfin_mac_device = {
- .name = "bfin_mac",
- .dev.platform_data = &bfin_mii_bus,
-};
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-static struct resource net2272_bfin_resources[] = {
- {
- .start = 0x20300000,
- .end = 0x20300000 + 0x100,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PF7,
- .end = IRQ_PF7,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct platform_device net2272_bfin_device = {
- .name = "net2272",
- .id = -1,
- .num_resources = ARRAY_SIZE(net2272_bfin_resources),
- .resource = net2272_bfin_resources,
-};
-#endif
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-/* all SPI peripherals info goes here */
-
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
-static struct mtd_partition bfin_spi_flash_partitions[] = {
- {
- .name = "bootloader(spi)",
- .size = 0x00020000,
- .offset = 0,
- .mask_flags = MTD_CAP_ROM
- }, {
- .name = "linux kernel(spi)",
- .size = 0xe0000,
- .offset = 0x20000
- }, {
- .name = "file system(spi)",
- .size = 0x700000,
- .offset = 0x00100000,
- }
-};
-
-static struct flash_platform_data bfin_spi_flash_data = {
- .name = "m25p80",
- .parts = bfin_spi_flash_partitions,
- .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
- .type = "m25p64",
-};
-
-/* SPI flash chip (m25p64) */
-static struct bfin5xx_spi_chip spi_flash_chip_info = {
- .enable_dma = 0, /* use dma transfer with this chip*/
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_SPI_ADC_BF533) \
- || defined(CONFIG_SPI_ADC_BF533_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
- .enable_dma = 1, /* use dma transfer with this chip*/
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
- .ctl_reg = 0x4, /* send zero */
- .enable_dma = 0,
- .bits_per_word = 8,
- .cs_change_per_word = 1,
-};
-#endif
-
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-
-static const struct ad7877_platform_data bfin_ad7877_ts_info = {
- .model = 7877,
- .vref_delay_usecs = 50, /* internal, no capacitor */
- .x_plate_ohms = 419,
- .y_plate_ohms = 486,
- .pressure_max = 1000,
- .pressure_min = 0,
- .stopacq_polarity = 1,
- .first_conversion_delay = 3,
- .acquisition_time = 1,
- .averaging = 1,
- .pen_down_acc_interval = 1,
-};
-#endif
-
-static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
- || defined(CONFIG_MTD_M25P80_MODULE)
- {
- /* the modalias must be the same as spi device driver name */
- .modalias = "m25p80", /* Name of spi_driver for this device */
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
- .platform_data = &bfin_spi_flash_data,
- .controller_data = &spi_flash_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-
-#if defined(CONFIG_SPI_ADC_BF533) \
- || defined(CONFIG_SPI_ADC_BF533_MODULE)
- {
- .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
- .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. */
- .platform_data = NULL, /* No spi_driver specific config */
- .controller_data = &spi_adc_chip_info,
- },
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
- || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
- {
- .modalias = "ad1836-spi",
- .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
- .controller_data = &ad1836_spi_chip_info,
- },
-#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
- {
- .modalias = "ad9960-spi",
- .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &ad9960_spi_chip_info,
- },
-#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "spi_mmc",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-#if defined(CONFIG_PBX)
- {
- .modalias = "fxs-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J11_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "fxo-spi",
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 8 - CONFIG_J19_JUMPER,
- .controller_data = &spi_si3xxx_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
- {
- .modalias = "ad7877",
- .platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PF6,
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &spi_ad7877_chip_info,
- },
-#endif
-};
-
-/* SPI controller data */
-static struct bfin5xx_spi_master bfin_spi0_info = {
- .num_chipselect = 8,
- .enable_dma = 1, /* master has the ability to do dma transfer */
- .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
-};
-
-/* SPI (0) */
-static struct resource bfin_spi0_resource[] = {
- [0] = {
- .start = SPI0_REGBASE,
- .end = SPI0_REGBASE + 0xFF,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = CH_SPI,
- .end = CH_SPI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bfin_spi0_device = {
- .name = "bfin-spi",
- .id = 0, /* Bus number */
- .num_resources = ARRAY_SIZE(bfin_spi0_resource),
- .resource = bfin_spi0_resource,
- .dev = {
- .platform_data = &bfin_spi0_info, /* Passed to driver */
- },
-};
-#endif /* spi master and devices */
-
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
-static struct platform_device bfin_fb_device = {
- .name = "bf537-lq035",
-};
-#endif
-
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
-static struct platform_device bfin_fb_adv7393_device = {
- .name = "bfin-adv7393",
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device bfin_uart_device = {
- .name = "bfin-uart",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_uart_resources),
- .resource = bfin_uart_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir0_device = {
- .name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir0_resources),
- .resource = bfin_sir0_resources,
-};
-#endif
-#ifdef CONFIG_BFIN_SIR1
-static struct resource bfin_sir1_resources[] = {
- {
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART1_RX,
- .end = IRQ_UART1_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART1_RX,
- .end = CH_UART1_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir1_device = {
- .name = "bfin_sir",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_sir1_resources),
- .resource = bfin_sir1_resources,
-};
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-static struct resource bfin_twi0_resource[] = {
- [0] = {
- .start = TWI0_REGBASE,
- .end = TWI0_REGBASE + 0xFF,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_TWI,
- .end = IRQ_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c_bfin_twi_device = {
- .name = "i2c-bfin-twi",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_twi0_resource),
- .resource = bfin_twi0_resource,
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-static struct platform_device bfin_sport0_uart_device = {
- .name = "bfin-sport-uart",
- .id = 0,
-};
-
-static struct platform_device bfin_sport1_uart_device = {
- .name = "bfin-sport-uart",
- .id = 1,
-};
-#endif
-
-static struct platform_device *stamp_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
- &bfin_pcmcia_cf_device,
-#endif
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
- &rtc_device,
-#endif
-
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
- &sl811_hcd_device,
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
- &smc91x_device,
-#endif
-
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
- &dm9000_device,
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
- &bfin_mii_bus,
- &bfin_mac_device,
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
- &net2272_bfin_device,
-#endif
-
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
- &bfin_isp1760_device,
-#endif
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &bfin_spi0_device,
-#endif
-
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
- &bfin_fb_device,
-#endif
-
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
- &bfin_fb_adv7393_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
- &bfin_uart_device,
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
- &bfin_sir0_device,
-#endif
-#ifdef CONFIG_BFIN_SIR1
- &bfin_sir1_device,
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
- &i2c_bfin_twi_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
- &bfin_sport0_uart_device,
- &bfin_sport1_uart_device,
-#endif
-};
-
-static int __init generic_init(void)
-{
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- spi_register_board_info(bfin_spi_board_info,
- ARRAY_SIZE(bfin_spi_board_info));
-#endif
-
- return 0;
-}
-
-arch_initcall(generic_init);
-
-void native_machine_restart(char *cmd)
-{
- /* workaround reboot hang when booting from SPI */
- if ((bfin_read_SYSCR() & 0x7) == 0x3)
- bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
-}
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-void bfin_get_ether_addr(char *addr)
-{
- random_ether_addr(addr);
- printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
-}
-EXPORT_SYMBOL(bfin_get_ether_addr);
-#endif
diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c
index db7d3a385e4..3c159819e55 100644
--- a/arch/blackfin/mach-bf537/boards/minotaur.c
+++ b/arch/blackfin/mach-bf537/boards/minotaur.c
@@ -134,9 +134,9 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -156,23 +156,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc_dummy",
+ .modalias = "mmc_spi",
.max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = 0,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
- {
- .modalias = "spi_mmc",
- .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 590eb3a139b..4e1de1e53f8 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -289,9 +289,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -364,23 +364,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad9960_spi_chip_info,
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 7,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 3f4f203a06e..53ad10f3cd7 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -108,9 +108,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -160,23 +160,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
- {
- .modalias = "spi_mmc_dummy",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 7,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
- .mode = SPI_MODE_3,
- },
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf537/include/mach/anomaly.h b/arch/blackfin/mach-bf537/include/mach/anomaly.h
index 9cb39121d1c..1bfd80c26c9 100644
--- a/arch/blackfin/mach-bf537/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf537/include/mach/anomaly.h
@@ -2,7 +2,7 @@
* File: include/asm-blackfin/mach-bf537/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
@@ -110,7 +110,7 @@
#define ANOMALY_05000301 (1)
/* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */
#define ANOMALY_05000304 (__SILICON_REVISION__ < 3)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
#define ANOMALY_05000305 (__SILICON_REVISION__ < 3)
/* SCKELOW Bit Does Not Maintain State Through Hibernate */
#define ANOMALY_05000307 (__SILICON_REVISION__ < 3)
@@ -168,9 +168,12 @@
#define ANOMALY_05000323 (0)
#define ANOMALY_05000353 (1)
#define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
#define ANOMALY_05000386 (1)
#define ANOMALY_05000412 (0)
#define ANOMALY_05000432 (0)
#define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
index b3f87e1d16a..9e34700844a 100644
--- a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART1_TX,
CH_UART1_RX,
#endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART1_CTS_PIN,
CONFIG_UART1_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-bf538/include/mach/anomaly.h b/arch/blackfin/mach-bf538/include/mach/anomaly.h
index e130b4f8a05..3a569982736 100644
--- a/arch/blackfin/mach-bf538/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf538/include/mach/anomaly.h
@@ -2,7 +2,7 @@
* File: include/asm-blackfin/mach-bf538/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
@@ -120,13 +120,17 @@
#define ANOMALY_05000198 (0)
#define ANOMALY_05000230 (0)
#define ANOMALY_05000263 (0)
+#define ANOMALY_05000305 (0)
#define ANOMALY_05000311 (0)
#define ANOMALY_05000323 (0)
#define ANOMALY_05000353 (1)
#define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
#define ANOMALY_05000386 (1)
#define ANOMALY_05000412 (0)
#define ANOMALY_05000432 (0)
#define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
index 40503b6b89a..3c2811ebecd 100644
--- a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART1_TX,
CH_UART1_RX,
#endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART1_CTS_PIN,
CONFIG_UART1_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h
index 23d03c52f4b..882e40ccf0d 100644
--- a/arch/blackfin/mach-bf548/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h
@@ -2,12 +2,12 @@
* File: include/asm-blackfin/mach-bf548/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
/* This file shoule be up to date with:
- * - Revision G, 08/07/2008; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
+ * - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
@@ -91,8 +91,6 @@
#define ANOMALY_05000371 (__SILICON_REVISION__ < 2)
/* USB DP/DM Data Pins May Lose State When Entering Hibernate */
#define ANOMALY_05000372 (__SILICON_REVISION__ < 1)
-/* Mobile DDR Operation Not Functional */
-#define ANOMALY_05000377 (1)
/* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */
#define ANOMALY_05000378 (__SILICON_REVISION__ < 2)
/* 16-Bit NAND FLASH Boot Mode Is Not Functional */
@@ -157,8 +155,22 @@
#define ANOMALY_05000429 (__SILICON_REVISION__ < 2)
/* Software System Reset Corrupts PLL_LOCKCNT Register */
#define ANOMALY_05000430 (__SILICON_REVISION__ >= 2)
+/* Incorrect Use of Stack in Lockbox Firmware During Authentication */
+#define ANOMALY_05000431 (__SILICON_REVISION__ < 3)
+/* OTP Write Accesses Not Supported */
+#define ANOMALY_05000442 (__SILICON_REVISION__ < 1)
/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */
#define ANOMALY_05000443 (1)
+/* CDMAPRIO and L2DMAPRIO Bits in the SYSCR Register Are Not Functional */
+#define ANOMALY_05000446 (1)
+/* UART IrDA Receiver Fails on Extended Bit Pulses */
+#define ANOMALY_05000447 (1)
+/* DDR Clock Duty Cycle Spec Violation (tCH, tCL) */
+#define ANOMALY_05000448 (__SILICON_REVISION__ == 1)
+/* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */
+#define ANOMALY_05000449 (__SILICON_REVISION__ == 1)
+/* USB DMA Mode 1 Short Packet Data Corruption */
+#define ANOMALY_05000450 (1
/* Anomalies that don't exist on this proc */
#define ANOMALY_05000125 (0)
@@ -171,6 +183,8 @@
#define ANOMALY_05000263 (0)
#define ANOMALY_05000266 (0)
#define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
+#define ANOMALY_05000305 (0)
#define ANOMALY_05000307 (0)
#define ANOMALY_05000311 (0)
#define ANOMALY_05000323 (0)
diff --git a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
index e4cf35e7ab9..c05e79cba25 100644
--- a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
@@ -63,7 +63,7 @@
#define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v)
#define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF)
-#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART2_CTSRTS)
# define CONFIG_SERIAL_BFIN_CTSRTS
# ifndef CONFIG_UART0_CTS_PIN
@@ -74,12 +74,12 @@
# define CONFIG_UART0_RTS_PIN -1
# endif
-# ifndef CONFIG_UART1_CTS_PIN
-# define CONFIG_UART1_CTS_PIN -1
+# ifndef CONFIG_UART2_CTS_PIN
+# define CONFIG_UART2_CTS_PIN -1
# endif
-# ifndef CONFIG_UART1_RTS_PIN
-# define CONFIG_UART1_RTS_PIN -1
+# ifndef CONFIG_UART2_RTS_PIN
+# define CONFIG_UART2_RTS_PIN -1
# endif
#endif
@@ -130,7 +130,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
@@ -144,6 +144,10 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART1_TX,
CH_UART1_RX,
#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ 0,
+ 0,
+#endif
},
#endif
#ifdef CONFIG_SERIAL_BFIN_UART2
@@ -154,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART2_TX,
CH_UART2_RX,
#endif
-#ifdef CONFIG_BFIN_UART2_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART2_CTS_PIN,
CONFIG_UART2_RTS_PIN,
#endif
@@ -168,6 +172,10 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART3_TX,
CH_UART3_RX,
#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ 0,
+ 0,
+#endif
},
#endif
};
diff --git a/arch/blackfin/mach-bf548/include/mach/irq.h b/arch/blackfin/mach-bf548/include/mach/irq.h
index 60299a71e09..f194625f682 100644
--- a/arch/blackfin/mach-bf548/include/mach/irq.h
+++ b/arch/blackfin/mach-bf548/include/mach/irq.h
@@ -123,8 +123,8 @@ Events (highest priority) EMU 0
#define IRQ_MXVR_ERROR BFIN_IRQ(51) /* MXVR Status (Error) Interrupt */
#define IRQ_MXVR_MSG BFIN_IRQ(52) /* MXVR Message Interrupt */
#define IRQ_MXVR_PKT BFIN_IRQ(53) /* MXVR Packet Interrupt */
-#define IRQ_EPP1_ERROR BFIN_IRQ(54) /* EPPI1 Error Interrupt */
-#define IRQ_EPP2_ERROR BFIN_IRQ(55) /* EPPI2 Error Interrupt */
+#define IRQ_EPPI1_ERROR BFIN_IRQ(54) /* EPPI1 Error Interrupt */
+#define IRQ_EPPI2_ERROR BFIN_IRQ(55) /* EPPI2 Error Interrupt */
#define IRQ_UART3_ERROR BFIN_IRQ(56) /* UART3 Status (Error) Interrupt */
#define IRQ_HOST_ERROR BFIN_IRQ(57) /* HOST Status (Error) Interrupt */
#define IRQ_PIXC_ERROR BFIN_IRQ(59) /* PIXC Status (Error) Interrupt */
@@ -361,8 +361,8 @@ Events (highest priority) EMU 0
#define IRQ_UART2_ERR IRQ_UART2_ERROR
#define IRQ_CAN0_ERR IRQ_CAN0_ERROR
#define IRQ_MXVR_ERR IRQ_MXVR_ERROR
-#define IRQ_EPP1_ERR IRQ_EPP1_ERROR
-#define IRQ_EPP2_ERR IRQ_EPP2_ERROR
+#define IRQ_EPPI1_ERR IRQ_EPPI1_ERROR
+#define IRQ_EPPI2_ERR IRQ_EPPI2_ERROR
#define IRQ_UART3_ERR IRQ_UART3_ERROR
#define IRQ_HOST_ERR IRQ_HOST_ERROR
#define IRQ_PIXC_ERR IRQ_PIXC_ERROR
diff --git a/arch/blackfin/mach-bf561/boards/Kconfig b/arch/blackfin/mach-bf561/boards/Kconfig
index e41a67b1fb5..e4bc6d7c5a6 100644
--- a/arch/blackfin/mach-bf561/boards/Kconfig
+++ b/arch/blackfin/mach-bf561/boards/Kconfig
@@ -19,9 +19,4 @@ config BFIN561_BLUETECHNIX_CM
help
CM-BF561 support for EVAL- and DEV-Board.
-config GENERIC_BF561_BOARD
- bool "Generic"
- help
- Generic or Custom board support.
-
endchoice
diff --git a/arch/blackfin/mach-bf561/boards/Makefile b/arch/blackfin/mach-bf561/boards/Makefile
index 04add010b56..3a152559e95 100644
--- a/arch/blackfin/mach-bf561/boards/Makefile
+++ b/arch/blackfin/mach-bf561/boards/Makefile
@@ -2,7 +2,6 @@
# arch/blackfin/mach-bf561/boards/Makefile
#
-obj-$(CONFIG_GENERIC_BF561_BOARD) += generic_board.o
obj-$(CONFIG_BFIN561_BLUETECHNIX_CM) += cm_bf561.o
obj-$(CONFIG_BFIN561_EZKIT) += ezkit.o
obj-$(CONFIG_BFIN561_TEPLA) += tepla.o
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 6880d1ebfe6..f623c6b0719 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -105,9 +105,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
};
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
- .enable_dma = 1,
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
.bits_per_word = 8,
};
#endif
@@ -155,14 +155,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
.controller_data = &ad9960_spi_chip_info,
},
#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
- .modalias = "spi_mmc",
+ .modalias = "mmc_spi",
.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
.bus_num = 0,
- .chip_select = CONFIG_SPI_MMC_CS_CHAN,
- .platform_data = NULL,
- .controller_data = &spi_mmc_chip_info,
+ .chip_select = 5,
+ .controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
diff --git a/arch/blackfin/mach-bf561/boards/generic_board.c b/arch/blackfin/mach-bf561/boards/generic_board.c
deleted file mode 100644
index 0ba366a0e69..00000000000
--- a/arch/blackfin/mach-bf561/boards/generic_board.c
+++ /dev/null
@@ -1,113 +0,0 @@
-/*
- * File: arch/blackfin/mach-bf561/generic_board.c
- * Based on: arch/blackfin/mach-bf533/ezkit.c
- * Author: Aidan Williams <aidan@nicta.com.au>
- *
- * Created:
- * Description:
- *
- * Modified:
- * Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-
-const char bfin_board_name[] = "UNKNOWN BOARD";
-
-/*
- * Driver needs to know address, irq and flag pin.
- */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
- {
- .start = 0x2C010300,
- .end = 0x2C010300 + 16,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PROG_INTB,
- .end = IRQ_PROG_INTB,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- }, {
- .start = IRQ_PF9,
- .end = IRQ_PF9,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir0_device = {
- .name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir0_resources),
- .resource = bfin_sir0_resources,
-};
-#endif
-#endif
-
-static struct platform_device *generic_board_devices[] __initdata = {
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
- &smc91x_device,
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
- &bfin_sir0_device,
-#endif
-#endif
-};
-
-static int __init generic_board_init(void)
-{
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- return platform_add_devices(generic_board_devices,
- ARRAY_SIZE(generic_board_devices));
-}
-
-arch_initcall(generic_board_init);
diff --git a/arch/blackfin/mach-bf561/include/mach/anomaly.h b/arch/blackfin/mach-bf561/include/mach/anomaly.h
index 1a9e1756282..d0b0b350644 100644
--- a/arch/blackfin/mach-bf561/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf561/include/mach/anomaly.h
@@ -2,7 +2,7 @@
* File: include/asm-blackfin/mach-bf561/anomaly.h
* Bugs: Enter bugs at http://blackfin.uclinux.org/
*
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
@@ -224,7 +224,7 @@
#define ANOMALY_05000301 (1)
/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
#define ANOMALY_05000302 (1)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
/* SCKELOW Bit Does Not Maintain State Through Hibernate */
#define ANOMALY_05000307 (__SILICON_REVISION__ < 5)
@@ -283,8 +283,11 @@
#define ANOMALY_05000273 (0)
#define ANOMALY_05000311 (0)
#define ANOMALY_05000353 (1)
+#define ANOMALY_05000380 (0)
#define ANOMALY_05000386 (1)
#define ANOMALY_05000432 (0)
#define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
#endif
diff --git a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
index 043bfcf26c5..ca8c5f64520 100644
--- a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
@@ -134,7 +134,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
CH_UART_TX,
CH_UART_RX,
#endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
CONFIG_UART0_CTS_PIN,
CONFIG_UART0_RTS_PIN,
#endif
diff --git a/arch/blackfin/mach-common/arch_checks.c b/arch/blackfin/mach-common/arch_checks.c
index 98133b968f7..80d39b2f9db 100644
--- a/arch/blackfin/mach-common/arch_checks.c
+++ b/arch/blackfin/mach-common/arch_checks.c
@@ -62,3 +62,12 @@
#if (CONFIG_BOOT_LOAD & 0x3)
# error "The kernel load address must be 4 byte aligned"
#endif
+
+/* The entire kernel must be able to make a 24bit pcrel call to start of L1 */
+#if ((0xffffffff - L1_CODE_START + 1) + CONFIG_BOOT_LOAD) > 0x1000000
+# error "The kernel load address is too high; keep it below 10meg for safety"
+#endif
+
+#if ANOMALY_05000448
+# error You are using a part with anomaly 05000448, this issue causes random memory read/write failures - that means random crashes.
+#endif
diff --git a/arch/blackfin/mach-common/cache.S b/arch/blackfin/mach-common/cache.S
index 3c98dacbf28..aa0648c6a9f 100644
--- a/arch/blackfin/mach-common/cache.S
+++ b/arch/blackfin/mach-common/cache.S
@@ -66,11 +66,33 @@
/* Invalidate all instruction cache lines assocoiated with this memory area */
ENTRY(_blackfin_icache_flush_range)
+/*
+ * Walkaround to avoid loading wrong instruction after invalidating icache
+ * and following sequence is met.
+ *
+ * 1) One instruction address is cached in the instruction cache.
+ * 2) This instruction in SDRAM is changed.
+ * 3) IFLASH[P0] is executed only once in blackfin_icache_flush_range().
+ * 4) This instruction is executed again, but the old one is loaded.
+ */
+ P0 = R0;
+ IFLUSH[P0];
do_flush IFLUSH, , nop
ENDPROC(_blackfin_icache_flush_range)
/* Flush all cache lines assocoiated with this area of memory. */
ENTRY(_blackfin_icache_dcache_flush_range)
+/*
+ * Walkaround to avoid loading wrong instruction after invalidating icache
+ * and following sequence is met.
+ *
+ * 1) One instruction address is cached in the instruction cache.
+ * 2) This instruction in SDRAM is changed.
+ * 3) IFLASH[P0] is executed only once in blackfin_icache_flush_range().
+ * 4) This instruction is executed again, but the old one is loaded.
+ */
+ P0 = R0;
+ IFLUSH[P0];
do_flush FLUSH, IFLUSH
ENDPROC(_blackfin_icache_dcache_flush_range)
diff --git a/arch/blackfin/mach-common/clocks-init.c b/arch/blackfin/mach-common/clocks-init.c
index 9dddb6f8cc8..35393651359 100644
--- a/arch/blackfin/mach-common/clocks-init.c
+++ b/arch/blackfin/mach-common/clocks-init.c
@@ -17,7 +17,7 @@
#define SDGCTL_WIDTH (1 << 31) /* SDRAM external data path width */
#define PLL_CTL_VAL \
(((CONFIG_VCO_MULT & 63) << 9) | CLKIN_HALF | \
- (PLL_BYPASS << 8) | (ANOMALY_05000265 ? 0x8000 : 0))
+ (PLL_BYPASS << 8) | (ANOMALY_05000305 ? 0 : 0x8000))
__attribute__((l1_text))
static void do_sync(void)
diff --git a/arch/blackfin/mach-common/dpmc_modes.S b/arch/blackfin/mach-common/dpmc_modes.S
index 4da50bcd930..8009a512fb1 100644
--- a/arch/blackfin/mach-common/dpmc_modes.S
+++ b/arch/blackfin/mach-common/dpmc_modes.S
@@ -376,10 +376,22 @@ ENTRY(_do_hibernate)
#endif
#ifdef PINT0_ASSIGN
+ PM_SYS_PUSH(PINT0_MASK_SET)
+ PM_SYS_PUSH(PINT1_MASK_SET)
+ PM_SYS_PUSH(PINT2_MASK_SET)
+ PM_SYS_PUSH(PINT3_MASK_SET)
PM_SYS_PUSH(PINT0_ASSIGN)
PM_SYS_PUSH(PINT1_ASSIGN)
PM_SYS_PUSH(PINT2_ASSIGN)
PM_SYS_PUSH(PINT3_ASSIGN)
+ PM_SYS_PUSH(PINT0_INVERT_SET)
+ PM_SYS_PUSH(PINT1_INVERT_SET)
+ PM_SYS_PUSH(PINT2_INVERT_SET)
+ PM_SYS_PUSH(PINT3_INVERT_SET)
+ PM_SYS_PUSH(PINT0_EDGE_SET)
+ PM_SYS_PUSH(PINT1_EDGE_SET)
+ PM_SYS_PUSH(PINT2_EDGE_SET)
+ PM_SYS_PUSH(PINT3_EDGE_SET)
#endif
PM_SYS_PUSH(EBIU_AMBCTL0)
@@ -714,10 +726,22 @@ ENTRY(_do_hibernate)
PM_SYS_POP(EBIU_AMBCTL0)
#ifdef PINT0_ASSIGN
+ PM_SYS_POP(PINT3_EDGE_SET)
+ PM_SYS_POP(PINT2_EDGE_SET)
+ PM_SYS_POP(PINT1_EDGE_SET)
+ PM_SYS_POP(PINT0_EDGE_SET)
+ PM_SYS_POP(PINT3_INVERT_SET)
+ PM_SYS_POP(PINT2_INVERT_SET)
+ PM_SYS_POP(PINT1_INVERT_SET)
+ PM_SYS_POP(PINT0_INVERT_SET)
PM_SYS_POP(PINT3_ASSIGN)
PM_SYS_POP(PINT2_ASSIGN)
PM_SYS_POP(PINT1_ASSIGN)
PM_SYS_POP(PINT0_ASSIGN)
+ PM_SYS_POP(PINT3_MASK_SET)
+ PM_SYS_POP(PINT2_MASK_SET)
+ PM_SYS_POP(PINT1_MASK_SET)
+ PM_SYS_POP(PINT0_MASK_SET)
#endif
#ifdef SICA_IWR1
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 88de053bbe8..21e65a339a2 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -600,6 +600,19 @@ ENTRY(_system_call)
p2 = [p2];
[p2+(TASK_THREAD+THREAD_KSP)] = sp;
+#ifdef CONFIG_IPIPE
+ r0 = sp;
+ SP += -12;
+ call ___ipipe_syscall_root;
+ SP += 12;
+ cc = r0 == 1;
+ if cc jump .Lsyscall_really_exit;
+ cc = r0 == -1;
+ if cc jump .Lresume_userspace;
+ r3 = [sp + PT_R3];
+ r4 = [sp + PT_R4];
+ p0 = [sp + PT_ORIG_P0];
+#endif /* CONFIG_IPIPE */
/* Check the System Call */
r7 = __NR_syscall;
@@ -654,6 +667,17 @@ ENTRY(_system_call)
r7 = r7 & r4;
.Lsyscall_resched:
+#ifdef CONFIG_IPIPE
+ cc = BITTST(r7, TIF_IRQ_SYNC);
+ if !cc jump .Lsyscall_no_irqsync;
+ [--sp] = reti;
+ r0 = [sp++];
+ SP += -12;
+ call ___ipipe_sync_root;
+ SP += 12;
+ jump .Lresume_userspace_1;
+.Lsyscall_no_irqsync:
+#endif
cc = BITTST(r7, TIF_NEED_RESCHED);
if !cc jump .Lsyscall_sigpending;
@@ -685,6 +709,10 @@ ENTRY(_system_call)
.Lsyscall_really_exit:
r5 = [sp + PT_RESERVED];
rets = r5;
+#ifdef CONFIG_IPIPE
+ [--sp] = reti;
+ r5 = [sp++];
+#endif /* CONFIG_IPIPE */
rts;
ENDPROC(_system_call)
@@ -771,6 +799,15 @@ _new_old_task:
ENDPROC(_resume)
ENTRY(_ret_from_exception)
+#ifdef CONFIG_IPIPE
+ [--sp] = rets;
+ SP += -12;
+ call ___ipipe_check_root
+ SP += 12
+ rets = [sp++];
+ cc = r0 == 0;
+ if cc jump 4f; /* not on behalf of Linux, get out */
+#endif /* CONFIG_IPIPE */
p2.l = lo(IPEND);
p2.h = hi(IPEND);
@@ -827,6 +864,28 @@ ENTRY(_ret_from_exception)
rts;
ENDPROC(_ret_from_exception)
+#ifdef CONFIG_IPIPE
+
+_sync_root_irqs:
+ [--sp] = reti; /* Reenable interrupts */
+ r0 = [sp++];
+ jump.l ___ipipe_sync_root
+
+_resume_kernel_from_int:
+ r0.l = _sync_root_irqs
+ r0.h = _sync_root_irqs
+ [--sp] = rets;
+ [--sp] = ( r7:4, p5:3 );
+ SP += -12;
+ call ___ipipe_call_irqtail
+ SP += 12;
+ ( r7:4, p5:3 ) = [sp++];
+ rets = [sp++];
+ rts
+#else
+#define _resume_kernel_from_int 2f
+#endif
+
ENTRY(_return_from_int)
/* If someone else already raised IRQ 15, do nothing. */
csync;
@@ -848,7 +907,7 @@ ENTRY(_return_from_int)
r1 = r0 - r1;
r2 = r0 & r1;
cc = r2 == 0;
- if !cc jump 2f;
+ if !cc jump _resume_kernel_from_int;
/* Lower the interrupt level to 15. */
p0.l = lo(EVT15);
diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index 43c4eb9acb6..0069c2dd462 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -235,6 +235,7 @@ ENDPROC(_evt_system_call)
#ifdef CONFIG_IPIPE
ENTRY(___ipipe_call_irqtail)
+ p0 = r0;
r0.l = 1f;
r0.h = 1f;
reti = r0;
@@ -242,9 +243,6 @@ ENTRY(___ipipe_call_irqtail)
1:
[--sp] = rets;
[--sp] = ( r7:4, p5:3 );
- p0.l = ___ipipe_irq_tail_hook;
- p0.h = ___ipipe_irq_tail_hook;
- p0 = [p0];
sp += -12;
call (p0);
sp += 12;
@@ -259,7 +257,7 @@ ENTRY(___ipipe_call_irqtail)
p0.h = hi(EVT14);
[p0] = r0;
csync;
- r0 = 0x401f;
+ r0 = 0x401f (z);
sti r0;
raise 14;
[--sp] = reti; /* IRQs on. */
@@ -277,11 +275,7 @@ ENTRY(___ipipe_call_irqtail)
p0.h = _bfin_irq_flags;
r0 = [p0];
sti r0;
-#if 0 /* FIXME: this actually raises scheduling latencies */
- /* Reenable interrupts */
- [--sp] = reti;
- r0 = [sp++];
-#endif
rts;
ENDPROC(___ipipe_call_irqtail)
+
#endif /* CONFIG_IPIPE */
diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c
index 202494568c6..a7d7b2dd405 100644
--- a/arch/blackfin/mach-common/ints-priority.c
+++ b/arch/blackfin/mach-common/ints-priority.c
@@ -161,11 +161,15 @@ static void bfin_core_unmask_irq(unsigned int irq)
static void bfin_internal_mask_irq(unsigned int irq)
{
+ unsigned long flags;
+
#ifdef CONFIG_BF53x
+ local_irq_save_hw(flags);
bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() &
~(1 << SIC_SYSIRQ(irq)));
#else
unsigned mask_bank, mask_bit;
+ local_irq_save_hw(flags);
mask_bank = SIC_SYSIRQ(irq) / 32;
mask_bit = SIC_SYSIRQ(irq) % 32;
bfin_write_SIC_IMASK(mask_bank, bfin_read_SIC_IMASK(mask_bank) &
@@ -175,15 +179,20 @@ static void bfin_internal_mask_irq(unsigned int irq)
~(1 << mask_bit));
#endif
#endif
+ local_irq_restore_hw(flags);
}
static void bfin_internal_unmask_irq(unsigned int irq)
{
+ unsigned long flags;
+
#ifdef CONFIG_BF53x
+ local_irq_save_hw(flags);
bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() |
(1 << SIC_SYSIRQ(irq)));
#else
unsigned mask_bank, mask_bit;
+ local_irq_save_hw(flags);
mask_bank = SIC_SYSIRQ(irq) / 32;
mask_bit = SIC_SYSIRQ(irq) % 32;
bfin_write_SIC_IMASK(mask_bank, bfin_read_SIC_IMASK(mask_bank) |
@@ -193,6 +202,7 @@ static void bfin_internal_unmask_irq(unsigned int irq)
(1 << mask_bit));
#endif
#endif
+ local_irq_restore_hw(flags);
}
#ifdef CONFIG_PM
@@ -390,7 +400,7 @@ static void bfin_demux_error_irq(unsigned int int_err_irq,
static inline void bfin_set_irq_handler(unsigned irq, irq_flow_handler_t handle)
{
#ifdef CONFIG_IPIPE
- _set_irq_handler(irq, handle_edge_irq);
+ _set_irq_handler(irq, handle_level_irq);
#else
struct irq_desc *desc = irq_desc + irq;
/* May not call generic set_irq_handler() due to spinlock
@@ -1055,13 +1065,18 @@ int __init init_arch_irq(void)
#endif
default:
#ifdef CONFIG_IPIPE
- /*
- * We want internal interrupt sources to be masked, because
- * ISRs may trigger interrupts recursively (e.g. DMA), but
- * interrupts are _not_ masked at CPU level. So let's handle
- * them as level interrupts.
- */
- set_irq_handler(irq, handle_level_irq);
+ /*
+ * We want internal interrupt sources to be
+ * masked, because ISRs may trigger interrupts
+ * recursively (e.g. DMA), but interrupts are
+ * _not_ masked at CPU level. So let's handle
+ * most of them as level interrupts, except
+ * the timer interrupt which is special.
+ */
+ if (irq == IRQ_SYSTMR || irq == IRQ_CORETMR)
+ set_irq_handler(irq, handle_simple_irq);
+ else
+ set_irq_handler(irq, handle_level_irq);
#else /* !CONFIG_IPIPE */
set_irq_handler(irq, handle_simple_irq);
#endif /* !CONFIG_IPIPE */
@@ -1123,9 +1138,8 @@ int __init init_arch_irq(void)
#ifdef CONFIG_IPIPE
for (irq = 0; irq < NR_IRQS; irq++) {
- struct irq_desc *desc = irq_desc + irq;
+ struct irq_desc *desc = irq_to_desc(irq);
desc->ic_prio = __ipipe_get_irq_priority(irq);
- desc->thr_prio = __ipipe_get_irqthread_priority(irq);
}
#endif /* CONFIG_IPIPE */
@@ -1208,76 +1222,21 @@ int __ipipe_get_irq_priority(unsigned irq)
return IVG15;
}
-int __ipipe_get_irqthread_priority(unsigned irq)
-{
- int ient, prio;
- int demux_irq;
-
- /* The returned priority value is rescaled to [0..IVG13+1]
- * with 0 being the lowest effective priority level. */
-
- if (irq <= IRQ_CORETMR)
- return IVG13 - irq + 1;
-
- /* GPIO IRQs are given the priority of the demux
- * interrupt. */
- if (IS_GPIOIRQ(irq)) {
-#if defined(CONFIG_BF54x)
- u32 bank = PINT_2_BANK(irq2pint_lut[irq - SYS_IRQS]);
- demux_irq = (bank == 0 ? IRQ_PINT0 :
- bank == 1 ? IRQ_PINT1 :
- bank == 2 ? IRQ_PINT2 :
- IRQ_PINT3);
-#elif defined(CONFIG_BF561)
- demux_irq = (irq >= IRQ_PF32 ? IRQ_PROG2_INTA :
- irq >= IRQ_PF16 ? IRQ_PROG1_INTA :
- IRQ_PROG0_INTA);
-#elif defined(CONFIG_BF52x)
- demux_irq = (irq >= IRQ_PH0 ? IRQ_PORTH_INTA :
- irq >= IRQ_PG0 ? IRQ_PORTG_INTA :
- IRQ_PORTF_INTA);
-#else
- demux_irq = irq;
-#endif
- return IVG13 - PRIO_GPIODEMUX(demux_irq) + 1;
- }
-
- /* The GPIO demux interrupt is given a lower priority
- * than the GPIO IRQs, so that its threaded handler
- * unmasks the interrupt line after the decoded IRQs
- * have been processed. */
- prio = PRIO_GPIODEMUX(irq);
- /* demux irq? */
- if (prio != -1)
- return IVG13 - prio;
-
- for (ient = 0; ient < NR_PERI_INTS; ient++) {
- struct ivgx *ivg = ivg_table + ient;
- if (ivg->irqno == irq) {
- for (prio = 0; prio <= IVG13-IVG7; prio++) {
- if (ivg7_13[prio].ifirst <= ivg &&
- ivg7_13[prio].istop > ivg)
- return IVG7 - prio;
- }
- }
- }
-
- return 0;
-}
-
/* Hw interrupts are disabled on entry (check SAVE_CONTEXT). */
#ifdef CONFIG_DO_IRQ_L1
__attribute__((l1_text))
#endif
asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs)
{
+ struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr();
+ struct ipipe_domain *this_domain = ipipe_current_domain;
struct ivgx *ivg_stop = ivg7_13[vec-IVG7].istop;
struct ivgx *ivg = ivg7_13[vec-IVG7].ifirst;
- int irq;
+ int irq, s;
if (likely(vec == EVT_IVTMR_P)) {
irq = IRQ_CORETMR;
- goto handle_irq;
+ goto core_tick;
}
SSYNC();
@@ -1319,24 +1278,39 @@ asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs)
irq = ivg->irqno;
if (irq == IRQ_SYSTMR) {
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+core_tick:
+#else
bfin_write_TIMER_STATUS(1); /* Latch TIMIL0 */
+#endif
/* This is basically what we need from the register frame. */
__raw_get_cpu_var(__ipipe_tick_regs).ipend = regs->ipend;
__raw_get_cpu_var(__ipipe_tick_regs).pc = regs->pc;
- if (!ipipe_root_domain_p)
- __raw_get_cpu_var(__ipipe_tick_regs).ipend |= 0x10;
- else
+ if (this_domain != ipipe_root_domain)
__raw_get_cpu_var(__ipipe_tick_regs).ipend &= ~0x10;
+ else
+ __raw_get_cpu_var(__ipipe_tick_regs).ipend |= 0x10;
}
-handle_irq:
+#ifndef CONFIG_GENERIC_CLOCKEVENTS
+core_tick:
+#endif
+ if (this_domain == ipipe_root_domain) {
+ s = __test_and_set_bit(IPIPE_SYNCDEFER_FLAG, &p->status);
+ barrier();
+ }
ipipe_trace_irq_entry(irq);
__ipipe_handle_irq(irq, regs);
- ipipe_trace_irq_exit(irq);
+ ipipe_trace_irq_exit(irq);
- if (ipipe_root_domain_p)
- return !test_bit(IPIPE_STALL_FLAG, &ipipe_root_cpudom_var(status));
+ if (this_domain == ipipe_root_domain) {
+ set_thread_flag(TIF_IRQ_SYNC);
+ if (!s) {
+ __clear_bit(IPIPE_SYNCDEFER_FLAG, &p->status);
+ return !test_bit(IPIPE_STALL_FLAG, &p->status);
+ }
+ }
return 0;
}
diff --git a/arch/blackfin/mach-common/smp.c b/arch/blackfin/mach-common/smp.c
index 77c99284709..93eab614607 100644
--- a/arch/blackfin/mach-common/smp.c
+++ b/arch/blackfin/mach-common/smp.c
@@ -158,10 +158,14 @@ static irqreturn_t ipi_handler(int irq, void *dev_instance)
kfree(msg);
break;
case BFIN_IPI_CALL_FUNC:
+ spin_unlock(&msg_queue->lock);
ipi_call_function(cpu, msg);
+ spin_lock(&msg_queue->lock);
break;
case BFIN_IPI_CPU_STOP:
+ spin_unlock(&msg_queue->lock);
ipi_cpu_stop(cpu);
+ spin_lock(&msg_queue->lock);
kfree(msg);
break;
default:
@@ -457,7 +461,7 @@ void smp_icache_flush_range_others(unsigned long start, unsigned long end)
smp_flush_data.start = start;
smp_flush_data.end = end;
- if (smp_call_function(&ipi_flush_icache, &smp_flush_data, 1))
+ if (smp_call_function(&ipi_flush_icache, &smp_flush_data, 0))
printk(KERN_WARNING "SMP: failed to run I-cache flush request on other CPUs\n");
}
EXPORT_SYMBOL_GPL(smp_icache_flush_range_others);
diff --git a/arch/blackfin/mm/init.c b/arch/blackfin/mm/init.c
index d0532b72bba..9c3629b9a68 100644
--- a/arch/blackfin/mm/init.c
+++ b/arch/blackfin/mm/init.c
@@ -104,7 +104,7 @@ void __init paging_init(void)
}
}
-asmlinkage void init_pda(void)
+asmlinkage void __init init_pda(void)
{
unsigned int cpu = raw_smp_processor_id();
diff --git a/arch/ia64/sn/pci/pcibr/pcibr_dma.c b/arch/ia64/sn/pci/pcibr/pcibr_dma.c
index e626e50a938..060df4aa991 100644
--- a/arch/ia64/sn/pci/pcibr/pcibr_dma.c
+++ b/arch/ia64/sn/pci/pcibr/pcibr_dma.c
@@ -135,11 +135,10 @@ pcibr_dmatrans_direct64(struct pcidev_info * info, u64 paddr,
if (SN_DMA_ADDRTYPE(dma_flags) == SN_DMA_ADDR_PHYS)
pci_addr = IS_PIC_SOFT(pcibus_info) ?
PHYS_TO_DMA(paddr) :
- PHYS_TO_TIODMA(paddr) | dma_attributes;
+ PHYS_TO_TIODMA(paddr);
else
- pci_addr = IS_PIC_SOFT(pcibus_info) ?
- paddr :
- paddr | dma_attributes;
+ pci_addr = paddr;
+ pci_addr |= dma_attributes;
/* Handle Bus mode */
if (IS_PCIX(pcibus_info))
diff --git a/arch/mips/include/asm/compat.h b/arch/mips/include/asm/compat.h
index ac5d541368e..6c5b40905dd 100644
--- a/arch/mips/include/asm/compat.h
+++ b/arch/mips/include/asm/compat.h
@@ -3,6 +3,8 @@
/*
* Architecture specific compatibility types
*/
+#include <linux/seccomp.h>
+#include <linux/thread_info.h>
#include <linux/types.h>
#include <asm/page.h>
#include <asm/ptrace.h>
@@ -218,4 +220,9 @@ struct compat_shmid64_ds {
compat_ulong_t __unused2;
};
+static inline int is_compat_task(void)
+{
+ return test_thread_flag(TIF_32BIT);
+}
+
#endif /* _ASM_COMPAT_H */
diff --git a/arch/x86/kernel/ds.c b/arch/x86/kernel/ds.c
index 169a120587b..87b67e3a765 100644
--- a/arch/x86/kernel/ds.c
+++ b/arch/x86/kernel/ds.c
@@ -729,7 +729,7 @@ struct pebs_tracer *ds_request_pebs(struct task_struct *task,
spin_unlock_irqrestore(&ds_lock, irq);
- ds_write_config(tracer->ds.context, &tracer->trace.ds, ds_bts);
+ ds_write_config(tracer->ds.context, &tracer->trace.ds, ds_pebs);
ds_resume_pebs(tracer);
return tracer;
@@ -1029,5 +1029,4 @@ void ds_copy_thread(struct task_struct *tsk, struct task_struct *father)
void ds_exit_thread(struct task_struct *tsk)
{
- WARN_ON(tsk->thread.ds_ctx);
}
diff --git a/block/blk-merge.c b/block/blk-merge.c
index a104593e70c..5a244f05360 100644
--- a/block/blk-merge.c
+++ b/block/blk-merge.c
@@ -39,14 +39,13 @@ void blk_recalc_rq_sectors(struct request *rq, int nsect)
}
static unsigned int __blk_recalc_rq_segments(struct request_queue *q,
- struct bio *bio,
- unsigned int *seg_size_ptr)
+ struct bio *bio)
{
unsigned int phys_size;
struct bio_vec *bv, *bvprv = NULL;
int cluster, i, high, highprv = 1;
unsigned int seg_size, nr_phys_segs;
- struct bio *fbio;
+ struct bio *fbio, *bbio;
if (!bio)
return 0;
@@ -87,26 +86,20 @@ new_segment:
seg_size = bv->bv_len;
highprv = high;
}
+ bbio = bio;
}
- if (seg_size_ptr)
- *seg_size_ptr = seg_size;
+ if (nr_phys_segs == 1 && seg_size > fbio->bi_seg_front_size)
+ fbio->bi_seg_front_size = seg_size;
+ if (seg_size > bbio->bi_seg_back_size)
+ bbio->bi_seg_back_size = seg_size;
return nr_phys_segs;
}
void blk_recalc_rq_segments(struct request *rq)
{
- unsigned int seg_size = 0, phys_segs;
-
- phys_segs = __blk_recalc_rq_segments(rq->q, rq->bio, &seg_size);
-
- if (phys_segs == 1 && seg_size > rq->bio->bi_seg_front_size)
- rq->bio->bi_seg_front_size = seg_size;
- if (seg_size > rq->biotail->bi_seg_back_size)
- rq->biotail->bi_seg_back_size = seg_size;
-
- rq->nr_phys_segments = phys_segs;
+ rq->nr_phys_segments = __blk_recalc_rq_segments(rq->q, rq->bio);
}
void blk_recount_segments(struct request_queue *q, struct bio *bio)
@@ -114,7 +107,7 @@ void blk_recount_segments(struct request_queue *q, struct bio *bio)
struct bio *nxt = bio->bi_next;
bio->bi_next = NULL;
- bio->bi_phys_segments = __blk_recalc_rq_segments(q, bio, NULL);
+ bio->bi_phys_segments = __blk_recalc_rq_segments(q, bio);
bio->bi_next = nxt;
bio->bi_flags |= (1 << BIO_SEG_VALID);
}
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index a603bbf9b1b..66e012cd327 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -582,18 +582,18 @@ static const struct pci_device_id ahci_pci_tbl[] = {
{ PCI_VDEVICE(NVIDIA, 0x0abd), board_ahci }, /* MCP79 */
{ PCI_VDEVICE(NVIDIA, 0x0abe), board_ahci }, /* MCP79 */
{ PCI_VDEVICE(NVIDIA, 0x0abf), board_ahci }, /* MCP79 */
- { PCI_VDEVICE(NVIDIA, 0x0bc8), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bc9), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bca), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bcb), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bcc), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bcd), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bce), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bcf), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bc4), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bc5), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bc6), board_ahci }, /* MCP7B */
- { PCI_VDEVICE(NVIDIA, 0x0bc7), board_ahci }, /* MCP7B */
+ { PCI_VDEVICE(NVIDIA, 0x0d84), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d85), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d86), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d87), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d88), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d89), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8a), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8b), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8c), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8d), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8e), board_ahci }, /* MCP89 */
+ { PCI_VDEVICE(NVIDIA, 0x0d8f), board_ahci }, /* MCP89 */
/* SiS */
{ PCI_VDEVICE(SI, 0x1184), board_ahci }, /* SiS 966 */
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 9fbf0595f3d..060bcd601f5 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1322,14 +1322,16 @@ static u64 ata_id_n_sectors(const u16 *id)
{
if (ata_id_has_lba(id)) {
if (ata_id_has_lba48(id))
- return ata_id_u64(id, 100);
+ return ata_id_u64(id, ATA_ID_LBA_CAPACITY_2);
else
- return ata_id_u32(id, 60);
+ return ata_id_u32(id, ATA_ID_LBA_CAPACITY);
} else {
if (ata_id_current_chs_valid(id))
- return ata_id_u32(id, 57);
+ return id[ATA_ID_CUR_CYLS] * id[ATA_ID_CUR_HEADS] *
+ id[ATA_ID_CUR_SECTORS];
else
- return id[1] * id[3] * id[6];
+ return id[ATA_ID_CYLS] * id[ATA_ID_HEADS] *
+ id[ATA_ID_SECTORS];
}
}
@@ -4612,7 +4614,7 @@ void ata_sg_clean(struct ata_queued_cmd *qc)
VPRINTK("unmapping %u sg elements\n", qc->n_elem);
if (qc->n_elem)
- dma_unmap_sg(ap->dev, sg, qc->n_elem, dir);
+ dma_unmap_sg(ap->dev, sg, qc->orig_n_elem, dir);
qc->flags &= ~ATA_QCFLAG_DMAMAP;
qc->sg = NULL;
@@ -4727,7 +4729,7 @@ static int ata_sg_setup(struct ata_queued_cmd *qc)
return -1;
DPRINTK("%d sg elements mapped\n", n_elem);
-
+ qc->orig_n_elem = qc->n_elem;
qc->n_elem = n_elem;
qc->flags |= ATA_QCFLAG_DMAMAP;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index ce2ef047533..ea890911d4f 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2423,11 +2423,14 @@ int ata_eh_reset(struct ata_link *link, int classify,
}
/* prereset() might have cleared ATA_EH_RESET. If so,
- * bang classes and return.
+ * bang classes, thaw and return.
*/
if (reset && !(ehc->i.action & ATA_EH_RESET)) {
ata_for_each_dev(dev, link, ALL)
classes[dev->devno] = ATA_DEV_NONE;
+ if ((ap->pflags & ATA_PFLAG_FROZEN) &&
+ ata_is_host_link(link))
+ ata_eh_thaw_port(ap);
rc = 0;
goto out;
}
@@ -2901,7 +2904,7 @@ static int atapi_eh_clear_ua(struct ata_device *dev)
int i;
for (i = 0; i < ATA_EH_UA_TRIES; i++) {
- u8 sense_buffer[SCSI_SENSE_BUFFERSIZE];
+ u8 *sense_buffer = dev->link->ap->sector_buf;
u8 sense_key = 0;
unsigned int err_mask;
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 55a8eed3f3a..f65b53785a8 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -2523,7 +2523,7 @@ static void __exit nv_exit(void)
module_init(nv_init);
module_exit(nv_exit);
module_param_named(adma, adma_enabled, bool, 0444);
-MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: true)");
+MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)");
module_param_named(swncq, swncq_enabled, bool, 0444);
MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)");
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index b5a06111463..4f9b6d79201 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -3606,11 +3606,9 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
if (cciss_hard_reset_controller(pdev) || cciss_reset_msi(pdev))
return -ENODEV;
- /* Some devices (notably the HP Smart Array 5i Controller)
- need a little pause here */
- schedule_timeout_uninterruptible(30*HZ);
-
- /* Now try to get the controller to respond to a no-op */
+ /* Now try to get the controller to respond to a no-op. Some
+ devices (notably the HP Smart Array 5i Controller) need
+ up to 30 seconds to respond. */
for (i=0; i<30; i++) {
if (cciss_noop(pdev) == 0)
break;
diff --git a/drivers/block/loop.c b/drivers/block/loop.c
index edbaac6c057..bf034557767 100644
--- a/drivers/block/loop.c
+++ b/drivers/block/loop.c
@@ -392,8 +392,7 @@ lo_splice_actor(struct pipe_inode_info *pipe, struct pipe_buffer *buf,
struct loop_device *lo = p->lo;
struct page *page = buf->page;
sector_t IV;
- size_t size;
- int ret;
+ int size, ret;
ret = buf->ops->confirm(pipe, buf);
if (unlikely(ret))
diff --git a/drivers/block/xen-blkfront.c b/drivers/block/xen-blkfront.c
index b6c8ce25435..8f905089b72 100644
--- a/drivers/block/xen-blkfront.c
+++ b/drivers/block/xen-blkfront.c
@@ -977,6 +977,8 @@ static void backend_changed(struct xenbus_device *dev,
break;
case XenbusStateClosing:
+ if (info->gd == NULL)
+ xenbus_dev_fatal(dev, -ENODEV, "gd is NULL");
bd = bdget_disk(info->gd, 0);
if (bd == NULL)
xenbus_dev_fatal(dev, -ENODEV, "bdget failed");
diff --git a/drivers/dca/dca-core.c b/drivers/dca/dca-core.c
index 33bd7534751..25b743abfb5 100644
--- a/drivers/dca/dca-core.c
+++ b/drivers/dca/dca-core.c
@@ -1,5 +1,5 @@
/*
- * Copyright(c) 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2007 - 2009 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c
index 732fa1ec36a..e190d8b3070 100644
--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -430,13 +430,15 @@ late_initcall(dmatest_init);
static void __exit dmatest_exit(void)
{
struct dmatest_chan *dtc, *_dtc;
+ struct dma_chan *chan;
list_for_each_entry_safe(dtc, _dtc, &dmatest_channels, node) {
list_del(&dtc->node);
+ chan = dtc->chan;
dmatest_cleanup_channel(dtc);
pr_debug("dmatest: dropped channel %s\n",
- dma_chan_name(dtc->chan));
- dma_release_channel(dtc->chan);
+ dma_chan_name(chan));
+ dma_release_channel(chan);
}
}
module_exit(dmatest_exit);
diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index 70126a60623..86d6da47f55 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -158,7 +158,8 @@ static void dma_start(struct fsl_dma_chan *fsl_chan)
static void dma_halt(struct fsl_dma_chan *fsl_chan)
{
- int i = 0;
+ int i;
+
DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr,
DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) | FSL_DMA_MR_CA,
32);
@@ -166,8 +167,11 @@ static void dma_halt(struct fsl_dma_chan *fsl_chan)
DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) & ~(FSL_DMA_MR_CS
| FSL_DMA_MR_EMS_EN | FSL_DMA_MR_CA), 32);
- while (!dma_is_idle(fsl_chan) && (i++ < 100))
+ for (i = 0; i < 100; i++) {
+ if (dma_is_idle(fsl_chan))
+ break;
udelay(10);
+ }
if (i >= 100 && !dma_is_idle(fsl_chan))
dev_err(fsl_chan->dev, "DMA halt timeout!\n");
}
diff --git a/drivers/dma/ioat.c b/drivers/dma/ioat.c
index 4105d6575b6..ed83dd9df19 100644
--- a/drivers/dma/ioat.c
+++ b/drivers/dma/ioat.c
@@ -1,6 +1,6 @@
/*
* Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 Intel Corporation.
+ * Copyright(c) 2007 - 2009 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
diff --git a/drivers/dma/ioat_dca.c b/drivers/dma/ioat_dca.c
index 6cf622da028..c012a1e1504 100644
--- a/drivers/dma/ioat_dca.c
+++ b/drivers/dma/ioat_dca.c
@@ -1,6 +1,6 @@
/*
* Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 Intel Corporation.
+ * Copyright(c) 2007 - 2009 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
@@ -49,6 +49,23 @@
#define DCA_TAG_MAP_MASK 0xDF
+/* expected tag map bytes for I/OAT ver.2 */
+#define DCA2_TAG_MAP_BYTE0 0x80
+#define DCA2_TAG_MAP_BYTE1 0x0
+#define DCA2_TAG_MAP_BYTE2 0x81
+#define DCA2_TAG_MAP_BYTE3 0x82
+#define DCA2_TAG_MAP_BYTE4 0x82
+
+/* verify if tag map matches expected values */
+static inline int dca2_tag_map_valid(u8 *tag_map)
+{
+ return ((tag_map[0] == DCA2_TAG_MAP_BYTE0) &&
+ (tag_map[1] == DCA2_TAG_MAP_BYTE1) &&
+ (tag_map[2] == DCA2_TAG_MAP_BYTE2) &&
+ (tag_map[3] == DCA2_TAG_MAP_BYTE3) &&
+ (tag_map[4] == DCA2_TAG_MAP_BYTE4));
+}
+
/*
* "Legacy" DCA systems do not implement the DCA register set in the
* I/OAT device. Software needs direct support for their tag mappings.
@@ -452,6 +469,13 @@ struct dca_provider *ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase)
ioatdca->tag_map[i] = 0;
}
+ if (!dca2_tag_map_valid(ioatdca->tag_map)) {
+ dev_err(&pdev->dev, "APICID_TAG_MAP set incorrectly by BIOS, "
+ "disabling DCA\n");
+ free_dca_provider(dca);
+ return NULL;
+ }
+
err = register_dca_provider(dca, &pdev->dev);
if (err) {
free_dca_provider(dca);
diff --git a/drivers/dma/ioat_dma.c b/drivers/dma/ioat_dma.c
index b3759c4b653..5905cd36bcd 100644
--- a/drivers/dma/ioat_dma.c
+++ b/drivers/dma/ioat_dma.c
@@ -1,6 +1,6 @@
/*
* Intel I/OAT DMA Linux driver
- * Copyright(c) 2004 - 2007 Intel Corporation.
+ * Copyright(c) 2004 - 2009 Intel Corporation.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
@@ -189,11 +189,13 @@ static int ioat_dma_enumerate_channels(struct ioatdma_device *device)
ioat_chan->xfercap = xfercap;
ioat_chan->desccount = 0;
INIT_DELAYED_WORK(&ioat_chan->work, ioat_dma_chan_reset_part2);
- if (ioat_chan->device->version != IOAT_VER_1_2) {
- writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE
- | IOAT_DMA_DCA_ANY_CPU,
- ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
- }
+ if (ioat_chan->device->version == IOAT_VER_2_0)
+ writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE |
+ IOAT_DMA_DCA_ANY_CPU,
+ ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
+ else if (ioat_chan->device->version == IOAT_VER_3_0)
+ writel(IOAT_DMA_DCA_ANY_CPU,
+ ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
spin_lock_init(&ioat_chan->cleanup_lock);
spin_lock_init(&ioat_chan->desc_lock);
INIT_LIST_HEAD(&ioat_chan->free_desc);
@@ -1169,9 +1171,8 @@ static void ioat_dma_memcpy_cleanup(struct ioat_dma_chan *ioat_chan)
* up if the client is done with the descriptor
*/
if (async_tx_test_ack(&desc->async_tx)) {
- list_del(&desc->node);
- list_add_tail(&desc->node,
- &ioat_chan->free_desc);
+ list_move_tail(&desc->node,
+ &ioat_chan->free_desc);
} else
desc->async_tx.cookie = 0;
} else {
@@ -1362,6 +1363,7 @@ static int ioat_dma_self_test(struct ioatdma_device *device)
dma_cookie_t cookie;
int err = 0;
struct completion cmp;
+ unsigned long tmo;
src = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
if (!src)
@@ -1413,9 +1415,10 @@ static int ioat_dma_self_test(struct ioatdma_device *device)
}
device->common.device_issue_pending(dma_chan);
- wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
- if (device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
+ if (tmo == 0 ||
+ device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
!= DMA_SUCCESS) {
dev_err(&device->pdev->dev,
"Self-test copy timed out, disabling\n");
@@ -1657,6 +1660,13 @@ struct ioatdma_device *ioat_dma_probe(struct pci_dev *pdev,
" %d channels, device version 0x%02x, driver version %s\n",
device->common.chancnt, device->version, IOAT_DMA_VERSION);
+ if (!device->common.chancnt) {
+ dev_err(&device->pdev->dev,
+ "Intel(R) I/OAT DMA Engine problem found: "
+ "zero channels detected\n");
+ goto err_setup_interrupts;
+ }
+
err = ioat_dma_setup_interrupts(device);
if (err)
goto err_setup_interrupts;
@@ -1696,6 +1706,9 @@ void ioat_dma_remove(struct ioatdma_device *device)
struct dma_chan *chan, *_chan;
struct ioat_dma_chan *ioat_chan;
+ if (device->version != IOAT_VER_3_0)
+ cancel_delayed_work(&device->work);
+
ioat_dma_remove_interrupts(device);
dma_async_device_unregister(&device->common);
@@ -1707,10 +1720,6 @@ void ioat_dma_remove(struct ioatdma_device *device)
pci_release_regions(device->pdev);
pci_disable_device(device->pdev);
- if (device->version != IOAT_VER_3_0) {
- cancel_delayed_work(&device->work);
- }
-
list_for_each_entry_safe(chan, _chan,
&device->common.channels, device_node) {
ioat_chan = to_ioat_chan(chan);
diff --git a/drivers/dma/ioatdma.h b/drivers/dma/ioatdma.h
index a3306d0e137..a52ff4bd460 100644
--- a/drivers/dma/ioatdma.h
+++ b/drivers/dma/ioatdma.h
@@ -1,5 +1,5 @@
/*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
@@ -29,7 +29,7 @@
#include <linux/pci_ids.h>
#include <net/tcp.h>
-#define IOAT_DMA_VERSION "3.30"
+#define IOAT_DMA_VERSION "3.64"
enum ioat_interrupt {
none = 0,
@@ -135,12 +135,14 @@ static inline void ioat_set_tcp_copy_break(struct ioatdma_device *dev)
#ifdef CONFIG_NET_DMA
switch (dev->version) {
case IOAT_VER_1_2:
- case IOAT_VER_3_0:
sysctl_tcp_dma_copybreak = 4096;
break;
case IOAT_VER_2_0:
sysctl_tcp_dma_copybreak = 2048;
break;
+ case IOAT_VER_3_0:
+ sysctl_tcp_dma_copybreak = 262144;
+ break;
}
#endif
}
diff --git a/drivers/dma/ioatdma_hw.h b/drivers/dma/ioatdma_hw.h
index f1ae2c776f7..afa57eef86c 100644
--- a/drivers/dma/ioatdma_hw.h
+++ b/drivers/dma/ioatdma_hw.h
@@ -1,5 +1,5 @@
/*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/ioatdma_registers.h b/drivers/dma/ioatdma_registers.h
index 827cb503cac..49bc277424f 100644
--- a/drivers/dma/ioatdma_registers.h
+++ b/drivers/dma/ioatdma_registers.h
@@ -1,5 +1,5 @@
/*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/iop-adma.c b/drivers/dma/iop-adma.c
index 647374acba9..16adbe61cfb 100644
--- a/drivers/dma/iop-adma.c
+++ b/drivers/dma/iop-adma.c
@@ -928,19 +928,19 @@ iop_adma_xor_zero_sum_self_test(struct iop_adma_device *device)
for (src_idx = 0; src_idx < IOP_ADMA_NUM_SRC_TEST; src_idx++) {
xor_srcs[src_idx] = alloc_page(GFP_KERNEL);
- if (!xor_srcs[src_idx])
- while (src_idx--) {
+ if (!xor_srcs[src_idx]) {
+ while (src_idx--)
__free_page(xor_srcs[src_idx]);
- return -ENOMEM;
- }
+ return -ENOMEM;
+ }
}
dest = alloc_page(GFP_KERNEL);
- if (!dest)
- while (src_idx--) {
+ if (!dest) {
+ while (src_idx--)
__free_page(xor_srcs[src_idx]);
- return -ENOMEM;
- }
+ return -ENOMEM;
+ }
/* Fill in src buffers */
for (src_idx = 0; src_idx < IOP_ADMA_NUM_SRC_TEST; src_idx++) {
diff --git a/drivers/dma/ipu/ipu_idmac.c b/drivers/dma/ipu/ipu_idmac.c
index 1f154d08e98..ae50a9d1a4e 100644
--- a/drivers/dma/ipu/ipu_idmac.c
+++ b/drivers/dma/ipu/ipu_idmac.c
@@ -729,7 +729,7 @@ static int ipu_init_channel_buffer(struct idmac_channel *ichan,
ichan->status = IPU_CHANNEL_READY;
- spin_unlock_irqrestore(ipu->lock, flags);
+ spin_unlock_irqrestore(&ipu->lock, flags);
return 0;
}
diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c
index 5d5d5b31867..cb7f26fb9f1 100644
--- a/drivers/dma/mv_xor.c
+++ b/drivers/dma/mv_xor.c
@@ -1019,19 +1019,19 @@ mv_xor_xor_self_test(struct mv_xor_device *device)
for (src_idx = 0; src_idx < MV_XOR_NUM_SRC_TEST; src_idx++) {
xor_srcs[src_idx] = alloc_page(GFP_KERNEL);
- if (!xor_srcs[src_idx])
- while (src_idx--) {
+ if (!xor_srcs[src_idx]) {
+ while (src_idx--)
__free_page(xor_srcs[src_idx]);
- return -ENOMEM;
- }
+ return -ENOMEM;
+ }
}
dest = alloc_page(GFP_KERNEL);
- if (!dest)
- while (src_idx--) {
+ if (!dest) {
+ while (src_idx--)
__free_page(xor_srcs[src_idx]);
- return -ENOMEM;
- }
+ return -ENOMEM;
+ }
/* Fill in src buffers */
for (src_idx = 0; src_idx < MV_XOR_NUM_SRC_TEST; src_idx++) {
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index e072903b12f..5ea3bfad172 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -721,6 +721,11 @@ config BLK_DEV_IDE_TX4939
depends on SOC_TX4939
select BLK_DEV_IDEDMA_SFF
+config BLK_DEV_IDE_AT91
+ tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
+ depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
+ select IDE_TIMINGS
+
config IDE_ARM
tristate "ARM IDE support"
depends on ARM && (ARCH_RPC || ARCH_SHARK)
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index d0e3d7d5b46..1c326d94aa6 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -116,3 +116,4 @@ obj-$(CONFIG_BLK_DEV_IDE_AU1XXX) += au1xxx-ide.o
obj-$(CONFIG_BLK_DEV_IDE_TX4938) += tx4938ide.o
obj-$(CONFIG_BLK_DEV_IDE_TX4939) += tx4939ide.o
+obj-$(CONFIG_BLK_DEV_IDE_AT91) += at91_ide.o
diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c
new file mode 100644
index 00000000000..1bb50f46388
--- /dev/null
+++ b/drivers/ide/at91_ide.c
@@ -0,0 +1,467 @@
+/*
+ * IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory Controller
+ * with Compact Flash True IDE logic
+ *
+ * Copyright (c) 2008, 2009 Kelvatek Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/ide.h>
+#include <linux/platform_device.h>
+
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91sam9263_matrix.h>
+
+#define DRV_NAME "at91_ide"
+
+#define perr(fmt, args...) pr_err(DRV_NAME ": " fmt, ##args)
+#define pdbg(fmt, args...) pr_debug("%s " fmt, __func__, ##args)
+
+/*
+ * Access to IDE device is possible through EBI Static Memory Controller
+ * with Compact Flash logic. For details see EBI and SMC datasheet sections
+ * of any microcontroller from AT91SAM9 family.
+ *
+ * Within SMC chip select address space, lines A[23:21] distinguish Compact
+ * Flash modes (I/O, common memory, attribute memory, True IDE). IDE modes are:
+ * 0x00c0000 - True IDE
+ * 0x00e0000 - Alternate True IDE (Alt Status Register)
+ *
+ * On True IDE mode Task File and Data Register are mapped at the same address.
+ * To distinguish access between these two different bus data width is used:
+ * 8Bit for Task File, 16Bit for Data I/O.
+ *
+ * After initialization we do 8/16 bit flipping (changes in SMC MODE register)
+ * only inside IDE callback routines which are serialized by IDE layer,
+ * so no additional locking needed.
+ */
+
+#define TASK_FILE 0x00c00000
+#define ALT_MODE 0x00e00000
+#define REGS_SIZE 8
+
+#define enter_16bit(cs, mode) do { \
+ mode = at91_sys_read(AT91_SMC_MODE(cs)); \
+ at91_sys_write(AT91_SMC_MODE(cs), mode | AT91_SMC_DBW_16); \
+} while (0)
+
+#define leave_16bit(cs, mode) at91_sys_write(AT91_SMC_MODE(cs), mode);
+
+static void set_smc_timings(const u8 chipselect, const u16 cycle,
+ const u16 setup, const u16 pulse,
+ const u16 data_float, int use_iordy)
+{
+ unsigned long mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+ AT91_SMC_BAT_SELECT;
+
+ /* disable or enable waiting for IORDY signal */
+ if (use_iordy)
+ mode |= AT91_SMC_EXNWMODE_READY;
+
+ /* add data float cycles if needed */
+ if (data_float)
+ mode |= AT91_SMC_TDF_(data_float);
+
+ at91_sys_write(AT91_SMC_MODE(chipselect), mode);
+
+ /* setup timings in SMC */
+ at91_sys_write(AT91_SMC_SETUP(chipselect), AT91_SMC_NWESETUP_(setup) |
+ AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(setup) |
+ AT91_SMC_NCS_RDSETUP_(0));
+ at91_sys_write(AT91_SMC_PULSE(chipselect), AT91_SMC_NWEPULSE_(pulse) |
+ AT91_SMC_NCS_WRPULSE_(cycle) |
+ AT91_SMC_NRDPULSE_(pulse) |
+ AT91_SMC_NCS_RDPULSE_(cycle));
+ at91_sys_write(AT91_SMC_CYCLE(chipselect), AT91_SMC_NWECYCLE_(cycle) |
+ AT91_SMC_NRDCYCLE_(cycle));
+}
+
+static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz)
+{
+ u64 tmp = ns;
+
+ tmp *= mck_hz;
+ tmp += 1000*1000*1000 - 1; /* round up */
+ do_div(tmp, 1000*1000*1000);
+ return (unsigned int) tmp;
+}
+
+static void apply_timings(const u8 chipselect, const u8 pio,
+ const struct ide_timing *timing, int use_iordy)
+{
+ unsigned int t0, t1, t2, t6z;
+ unsigned int cycle, setup, pulse, data_float;
+ unsigned int mck_hz;
+ struct clk *mck;
+
+ /* see table 22 of Compact Flash standard 4.1 for the meaning,
+ * we do not stretch active (t2) time, so setup (t1) + hold time (th)
+ * assure at least minimal recovery (t2i) time */
+ t0 = timing->cyc8b;
+ t1 = timing->setup;
+ t2 = timing->act8b;
+ t6z = (pio < 5) ? 30 : 20;
+
+ pdbg("t0=%u t1=%u t2=%u t6z=%u\n", t0, t1, t2, t6z);
+
+ mck = clk_get(NULL, "mck");
+ BUG_ON(IS_ERR(mck));
+ mck_hz = clk_get_rate(mck);
+ pdbg("mck_hz=%u\n", mck_hz);
+
+ cycle = calc_mck_cycles(t0, mck_hz);
+ setup = calc_mck_cycles(t1, mck_hz);
+ pulse = calc_mck_cycles(t2, mck_hz);
+ data_float = calc_mck_cycles(t6z, mck_hz);
+
+ pdbg("cycle=%u setup=%u pulse=%u data_float=%u\n",
+ cycle, setup, pulse, data_float);
+
+ set_smc_timings(chipselect, cycle, setup, pulse, data_float, use_iordy);
+}
+
+static void at91_ide_input_data(ide_drive_t *drive, struct request *rq,
+ void *buf, unsigned int len)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_io_ports *io_ports = &hwif->io_ports;
+ u8 chipselect = hwif->select_data;
+ unsigned long mode;
+
+ pdbg("cs %u buf %p len %d\n", chipselect, buf, len);
+
+ len++;
+
+ enter_16bit(chipselect, mode);
+ __ide_mm_insw((void __iomem *) io_ports->data_addr, buf, len / 2);
+ leave_16bit(chipselect, mode);
+}
+
+static void at91_ide_output_data(ide_drive_t *drive, struct request *rq,
+ void *buf, unsigned int len)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_io_ports *io_ports = &hwif->io_ports;
+ u8 chipselect = hwif->select_data;
+ unsigned long mode;
+
+ pdbg("cs %u buf %p len %d\n", chipselect, buf, len);
+
+ enter_16bit(chipselect, mode);
+ __ide_mm_outsw((void __iomem *) io_ports->data_addr, buf, len / 2);
+ leave_16bit(chipselect, mode);
+}
+
+static u8 ide_mm_inb(unsigned long port)
+{
+ return readb((void __iomem *) port);
+}
+
+static void ide_mm_outb(u8 value, unsigned long port)
+{
+ writeb(value, (void __iomem *) port);
+}
+
+static void at91_ide_tf_load(ide_drive_t *drive, ide_task_t *task)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_io_ports *io_ports = &hwif->io_ports;
+ struct ide_taskfile *tf = &task->tf;
+ u8 HIHI = (task->tf_flags & IDE_TFLAG_LBA48) ? 0xE0 : 0xEF;
+
+ if (task->tf_flags & IDE_TFLAG_FLAGGED)
+ HIHI = 0xFF;
+
+ if (task->tf_flags & IDE_TFLAG_OUT_DATA) {
+ u16 data = (tf->hob_data << 8) | tf->data;
+
+ at91_ide_output_data(drive, NULL, &data, 2);
+ }
+
+ if (task->tf_flags & IDE_TFLAG_OUT_HOB_FEATURE)
+ ide_mm_outb(tf->hob_feature, io_ports->feature_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_HOB_NSECT)
+ ide_mm_outb(tf->hob_nsect, io_ports->nsect_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAL)
+ ide_mm_outb(tf->hob_lbal, io_ports->lbal_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAM)
+ ide_mm_outb(tf->hob_lbam, io_ports->lbam_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAH)
+ ide_mm_outb(tf->hob_lbah, io_ports->lbah_addr);
+
+ if (task->tf_flags & IDE_TFLAG_OUT_FEATURE)
+ ide_mm_outb(tf->feature, io_ports->feature_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_NSECT)
+ ide_mm_outb(tf->nsect, io_ports->nsect_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_LBAL)
+ ide_mm_outb(tf->lbal, io_ports->lbal_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_LBAM)
+ ide_mm_outb(tf->lbam, io_ports->lbam_addr);
+ if (task->tf_flags & IDE_TFLAG_OUT_LBAH)
+ ide_mm_outb(tf->lbah, io_ports->lbah_addr);
+
+ if (task->tf_flags & IDE_TFLAG_OUT_DEVICE)
+ ide_mm_outb((tf->device & HIHI) | drive->select, io_ports->device_addr);
+}
+
+static void at91_ide_tf_read(ide_drive_t *drive, ide_task_t *task)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_io_ports *io_ports = &hwif->io_ports;
+ struct ide_taskfile *tf = &task->tf;
+
+ if (task->tf_flags & IDE_TFLAG_IN_DATA) {
+ u16 data;
+
+ at91_ide_input_data(drive, NULL, &data, 2);
+ tf->data = data & 0xff;
+ tf->hob_data = (data >> 8) & 0xff;
+ }
+
+ /* be sure we're looking at the low order bits */
+ ide_mm_outb(ATA_DEVCTL_OBS & ~0x80, io_ports->ctl_addr);
+
+ if (task->tf_flags & IDE_TFLAG_IN_FEATURE)
+ tf->feature = ide_mm_inb(io_ports->feature_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_NSECT)
+ tf->nsect = ide_mm_inb(io_ports->nsect_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_LBAL)
+ tf->lbal = ide_mm_inb(io_ports->lbal_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_LBAM)
+ tf->lbam = ide_mm_inb(io_ports->lbam_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_LBAH)
+ tf->lbah = ide_mm_inb(io_ports->lbah_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_DEVICE)
+ tf->device = ide_mm_inb(io_ports->device_addr);
+
+ if (task->tf_flags & IDE_TFLAG_LBA48) {
+ ide_mm_outb(ATA_DEVCTL_OBS | 0x80, io_ports->ctl_addr);
+
+ if (task->tf_flags & IDE_TFLAG_IN_HOB_FEATURE)
+ tf->hob_feature = ide_mm_inb(io_ports->feature_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_HOB_NSECT)
+ tf->hob_nsect = ide_mm_inb(io_ports->nsect_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAL)
+ tf->hob_lbal = ide_mm_inb(io_ports->lbal_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAM)
+ tf->hob_lbam = ide_mm_inb(io_ports->lbam_addr);
+ if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAH)
+ tf->hob_lbah = ide_mm_inb(io_ports->lbah_addr);
+ }
+}
+
+static void at91_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+ struct ide_timing *timing;
+ u8 chipselect = drive->hwif->select_data;
+ int use_iordy = 0;
+
+ pdbg("chipselect %u pio %u\n", chipselect, pio);
+
+ timing = ide_timing_find_mode(XFER_PIO_0 + pio);
+ BUG_ON(!timing);
+
+ if ((pio > 2 || ata_id_has_iordy(drive->id)) &&
+ !(ata_id_is_cfa(drive->id) && pio > 4))
+ use_iordy = 1;
+
+ apply_timings(chipselect, pio, timing, use_iordy);
+}
+
+static const struct ide_tp_ops at91_ide_tp_ops = {
+ .exec_command = ide_exec_command,
+ .read_status = ide_read_status,
+ .read_altstatus = ide_read_altstatus,
+ .set_irq = ide_set_irq,
+
+ .tf_load = at91_ide_tf_load,
+ .tf_read = at91_ide_tf_read,
+
+ .input_data = at91_ide_input_data,
+ .output_data = at91_ide_output_data,
+};
+
+static const struct ide_port_ops at91_ide_port_ops = {
+ .set_pio_mode = at91_ide_set_pio_mode,
+};
+
+static const struct ide_port_info at91_ide_port_info __initdata = {
+ .port_ops = &at91_ide_port_ops,
+ .tp_ops = &at91_ide_tp_ops,
+ .host_flags = IDE_HFLAG_MMIO | IDE_HFLAG_NO_DMA | IDE_HFLAG_SINGLE |
+ IDE_HFLAG_NO_IO_32BIT | IDE_HFLAG_UNMASK_IRQS,
+ .pio_mask = ATA_PIO5,
+};
+
+/*
+ * If interrupt is delivered through GPIO, IRQ are triggered on falling
+ * and rising edge of signal. Whereas IDE device request interrupt on high
+ * level (rising edge in our case). This mean we have fake interrupts, so
+ * we need to check interrupt pin and exit instantly from ISR when line
+ * is on low level.
+ */
+
+irqreturn_t at91_irq_handler(int irq, void *dev_id)
+{
+ int ntries = 8;
+ int pin_val1, pin_val2;
+
+ /* additional deglitch, line can be noisy in badly designed PCB */
+ do {
+ pin_val1 = at91_get_gpio_value(irq);
+ pin_val2 = at91_get_gpio_value(irq);
+ } while (pin_val1 != pin_val2 && --ntries > 0);
+
+ if (pin_val1 == 0 || ntries <= 0)
+ return IRQ_HANDLED;
+
+ return ide_intr(irq, dev_id);
+}
+
+static int __init at91_ide_probe(struct platform_device *pdev)
+{
+ int ret;
+ hw_regs_t hw;
+ hw_regs_t *hws[] = { &hw, NULL, NULL, NULL };
+ struct ide_host *host;
+ struct resource *res;
+ unsigned long tf_base = 0, ctl_base = 0;
+ struct at91_cf_data *board = pdev->dev.platform_data;
+
+ if (!board)
+ return -ENODEV;
+
+ if (board->det_pin && at91_get_gpio_value(board->det_pin) != 0) {
+ perr("no device detected\n");
+ return -ENODEV;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ perr("can't get memory resource\n");
+ return -ENODEV;
+ }
+
+ if (!devm_request_mem_region(&pdev->dev, res->start + TASK_FILE,
+ REGS_SIZE, "ide") ||
+ !devm_request_mem_region(&pdev->dev, res->start + ALT_MODE,
+ REGS_SIZE, "alt")) {
+ perr("memory resources in use\n");
+ return -EBUSY;
+ }
+
+ pdbg("chipselect %u irq %u res %08lx\n", board->chipselect,
+ board->irq_pin, (unsigned long) res->start);
+
+ tf_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + TASK_FILE,
+ REGS_SIZE);
+ ctl_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + ALT_MODE,
+ REGS_SIZE);
+ if (!tf_base || !ctl_base) {
+ perr("can't map memory regions\n");
+ return -EBUSY;
+ }
+
+ memset(&hw, 0, sizeof(hw));
+
+ if (board->flags & AT91_IDE_SWAP_A0_A2) {
+ /* workaround for stupid hardware bug */
+ hw.io_ports.data_addr = tf_base + 0;
+ hw.io_ports.error_addr = tf_base + 4;
+ hw.io_ports.nsect_addr = tf_base + 2;
+ hw.io_ports.lbal_addr = tf_base + 6;
+ hw.io_ports.lbam_addr = tf_base + 1;
+ hw.io_ports.lbah_addr = tf_base + 5;
+ hw.io_ports.device_addr = tf_base + 3;
+ hw.io_ports.command_addr = tf_base + 7;
+ hw.io_ports.ctl_addr = ctl_base + 3;
+ } else
+ ide_std_init_ports(&hw, tf_base, ctl_base + 6);
+
+ hw.irq = board->irq_pin;
+ hw.chipset = ide_generic;
+ hw.dev = &pdev->dev;
+
+ host = ide_host_alloc(&at91_ide_port_info, hws);
+ if (!host) {
+ perr("failed to allocate ide host\n");
+ return -ENOMEM;
+ }
+
+ /* setup Static Memory Controller - PIO 0 as default */
+ apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
+
+ /* with GPIO interrupt we have to do quirks in handler */
+ if (board->irq_pin >= PIN_BASE)
+ host->irq_handler = at91_irq_handler;
+
+ host->ports[0]->select_data = board->chipselect;
+
+ ret = ide_host_register(host, &at91_ide_port_info, hws);
+ if (ret) {
+ perr("failed to register ide host\n");
+ goto err_free_host;
+ }
+ platform_set_drvdata(pdev, host);
+ return 0;
+
+err_free_host:
+ ide_host_free(host);
+ return ret;
+}
+
+static int __exit at91_ide_remove(struct platform_device *pdev)
+{
+ struct ide_host *host = platform_get_drvdata(pdev);
+
+ ide_host_remove(host);
+ return 0;
+}
+
+static struct platform_driver at91_ide_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(at91_ide_remove),
+};
+
+static int __init at91_ide_init(void)
+{
+ return platform_driver_probe(&at91_ide_driver, at91_ide_probe);
+}
+
+static void __exit at91_ide_exit(void)
+{
+ platform_driver_unregister(&at91_ide_driver);
+}
+
+module_init(at91_ide_init);
+module_exit(at91_ide_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stanislaw Gruszka <stf_xl@wp.pl>");
+
diff --git a/drivers/ide/ide-disk_proc.c b/drivers/ide/ide-disk_proc.c
index 1146f4204c6..1f86dcbd2b1 100644
--- a/drivers/ide/ide-disk_proc.c
+++ b/drivers/ide/ide-disk_proc.c
@@ -125,5 +125,5 @@ const struct ide_proc_devset ide_disk_settings[] = {
IDE_PROC_DEVSET(multcount, 0, 16),
IDE_PROC_DEVSET(nowerr, 0, 1),
IDE_PROC_DEVSET(wcache, 0, 1),
- { 0 },
+ { NULL },
};
diff --git a/drivers/ide/ide-floppy_proc.c b/drivers/ide/ide-floppy_proc.c
index 3ec762cb60a..fcd4d8153df 100644
--- a/drivers/ide/ide-floppy_proc.c
+++ b/drivers/ide/ide-floppy_proc.c
@@ -29,5 +29,5 @@ const struct ide_proc_devset ide_floppy_settings[] = {
IDE_PROC_DEVSET(bios_head, 0, 255),
IDE_PROC_DEVSET(bios_sect, 0, 63),
IDE_PROC_DEVSET(ticks, 0, 255),
- { 0 },
+ { NULL },
};
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 9ee51adf567..a9a6c208288 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -908,7 +908,7 @@ void ide_timer_expiry (unsigned long data)
ide_drive_t *uninitialized_var(drive);
ide_handler_t *handler;
unsigned long flags;
- unsigned long wait = -1;
+ int wait = -1;
int plug_device = 0;
spin_lock_irqsave(&hwif->lock, flags);
@@ -1162,6 +1162,7 @@ out_early:
return irq_ret;
}
+EXPORT_SYMBOL_GPL(ide_intr);
/**
* ide_do_drive_cmd - issue IDE special command
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 753b92ebe0a..b1892bd95c6 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -315,6 +315,8 @@ void ide_output_data(ide_drive_t *drive, struct request *rq, void *buf,
u8 io_32bit = drive->io_32bit;
u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0;
+ len++;
+
if (io_32bit) {
unsigned long uninitialized_var(flags);
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index ce0818a993f..ee8e3e7cad5 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -950,6 +950,7 @@ static int ide_port_setup_devices(ide_hwif_t *hwif)
static int init_irq (ide_hwif_t *hwif)
{
struct ide_io_ports *io_ports = &hwif->io_ports;
+ irq_handler_t irq_handler;
int sa = 0;
mutex_lock(&ide_cfg_mtx);
@@ -959,6 +960,10 @@ static int init_irq (ide_hwif_t *hwif)
hwif->timer.function = &ide_timer_expiry;
hwif->timer.data = (unsigned long)hwif;
+ irq_handler = hwif->host->irq_handler;
+ if (irq_handler == NULL)
+ irq_handler = ide_intr;
+
#if defined(__mc68000__)
sa = IRQF_SHARED;
#endif /* __mc68000__ */
@@ -969,7 +974,7 @@ static int init_irq (ide_hwif_t *hwif)
if (io_ports->ctl_addr)
hwif->tp_ops->set_irq(hwif, 1);
- if (request_irq(hwif->irq, &ide_intr, sa, hwif->name, hwif))
+ if (request_irq(hwif->irq, irq_handler, sa, hwif->name, hwif))
goto out_up;
if (!hwif->rqsize) {
diff --git a/drivers/ide/ide-proc.c b/drivers/ide/ide-proc.c
index 1d8978b3314..a7b9287ee0d 100644
--- a/drivers/ide/ide-proc.c
+++ b/drivers/ide/ide-proc.c
@@ -231,7 +231,7 @@ static const struct ide_proc_devset ide_generic_settings[] = {
IDE_PROC_DEVSET(pio_mode, 0, 255),
IDE_PROC_DEVSET(unmaskirq, 0, 1),
IDE_PROC_DEVSET(using_dma, 0, 1),
- { 0 },
+ { NULL },
};
static void proc_ide_settings_warn(void)
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index bb450a7608c..4e6181c7bbd 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -2166,7 +2166,7 @@ static const struct ide_proc_devset idetape_settings[] = {
__IDE_PROC_DEVSET(speed, 0, 0xffff, NULL, NULL),
__IDE_PROC_DEVSET(tdsc, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX,
mulf_tdsc, divf_tdsc),
- { 0 },
+ { NULL },
};
#endif
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index 9c50e6f1c23..34ce2703d29 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -248,12 +248,15 @@ mmc_send_cxd_data(struct mmc_card *card, struct mmc_host *host,
sg_init_one(&sg, data_buf, len);
- /*
- * The spec states that CSR and CID accesses have a timeout
- * of 64 clock cycles.
- */
- data.timeout_ns = 0;
- data.timeout_clks = 64;
+ if (opcode == MMC_SEND_CSD || opcode == MMC_SEND_CID) {
+ /*
+ * The spec states that CSR and CID accesses have a timeout
+ * of 64 clock cycles.
+ */
+ data.timeout_ns = 0;
+ data.timeout_clks = 64;
+ } else
+ mmc_set_data_timeout(&data, card);
mmc_wait_for_req(host, &mrq);
diff --git a/drivers/watchdog/gef_wdt.c b/drivers/watchdog/gef_wdt.c
index f0c2b7a1a17..734d9806a87 100644
--- a/drivers/watchdog/gef_wdt.c
+++ b/drivers/watchdog/gef_wdt.c
@@ -269,7 +269,7 @@ static int __devinit gef_wdt_probe(struct of_device *dev,
bus_clk = 133; /* in MHz */
freq = fsl_get_sys_freq();
- if (freq > 0)
+ if (freq != -1)
bus_clk = freq;
/* Map devices registers into memory */
diff --git a/drivers/watchdog/ks8695_wdt.c b/drivers/watchdog/ks8695_wdt.c
index 0b798fdaa37..74c92d38411 100644
--- a/drivers/watchdog/ks8695_wdt.c
+++ b/drivers/watchdog/ks8695_wdt.c
@@ -21,6 +21,7 @@
#include <linux/watchdog.h>
#include <linux/io.h>
#include <linux/uaccess.h>
+#include <mach/timex.h>
#include <mach/regs-timer.h>
#define WDT_DEFAULT_TIME 5 /* seconds */
diff --git a/drivers/watchdog/orion5x_wdt.c b/drivers/watchdog/orion5x_wdt.c
index 14a339f58b6..b64ae1a1783 100644
--- a/drivers/watchdog/orion5x_wdt.c
+++ b/drivers/watchdog/orion5x_wdt.c
@@ -29,6 +29,7 @@
#define WDT_EN 0x0010
#define WDT_VAL (TIMER_VIRT_BASE + 0x0024)
+#define ORION5X_TCLK 166666667
#define WDT_MAX_DURATION (0xffffffff / ORION5X_TCLK)
#define WDT_IN_USE 0
#define WDT_OK_TO_CLOSE 1
diff --git a/drivers/watchdog/rc32434_wdt.c b/drivers/watchdog/rc32434_wdt.c
index 57027f4653c..f3553fa40b1 100644
--- a/drivers/watchdog/rc32434_wdt.c
+++ b/drivers/watchdog/rc32434_wdt.c
@@ -34,104 +34,89 @@
#include <asm/time.h>
#include <asm/mach-rc32434/integ.h>
-#define MAX_TIMEOUT 20
-#define RC32434_WDT_INTERVAL (15 * HZ)
-
-#define VERSION "0.2"
+#define VERSION "0.4"
static struct {
- struct completion stop;
- int running;
- struct timer_list timer;
- int queue;
- int default_ticks;
unsigned long inuse;
} rc32434_wdt_device;
static struct integ __iomem *wdt_reg;
-static int ticks = 100 * HZ;
static int expect_close;
-static int timeout;
+
+/* Board internal clock speed in Hz,
+ * the watchdog timer ticks at. */
+extern unsigned int idt_cpu_freq;
+
+/* translate wtcompare value to seconds and vice versa */
+#define WTCOMP2SEC(x) (x / idt_cpu_freq)
+#define SEC2WTCOMP(x) (x * idt_cpu_freq)
+
+/* Use a default timeout of 20s. This should be
+ * safe for CPU clock speeds up to 400MHz, as
+ * ((2 ^ 32) - 1) / (400MHz / 2) = 21s. */
+#define WATCHDOG_TIMEOUT 20
+
+static int timeout = WATCHDOG_TIMEOUT;
static int nowayout = WATCHDOG_NOWAYOUT;
module_param(nowayout, int, 0);
MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
__MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+/* apply or and nand masks to data read from addr and write back */
+#define SET_BITS(addr, or, nand) \
+ writel((readl(&addr) | or) & ~nand, &addr)
static void rc32434_wdt_start(void)
{
- u32 val;
-
- if (!rc32434_wdt_device.inuse) {
- writel(0, &wdt_reg->wtcount);
+ u32 or, nand;
- val = RC32434_ERR_WRE;
- writel(readl(&wdt_reg->errcs) | val, &wdt_reg->errcs);
+ /* zero the counter before enabling */
+ writel(0, &wdt_reg->wtcount);
- val = RC32434_WTC_EN;
- writel(readl(&wdt_reg->wtc) | val, &wdt_reg->wtc);
- }
- rc32434_wdt_device.running++;
-}
+ /* don't generate a non-maskable interrupt,
+ * do a warm reset instead */
+ nand = 1 << RC32434_ERR_WNE;
+ or = 1 << RC32434_ERR_WRE;
-static void rc32434_wdt_stop(void)
-{
- u32 val;
+ /* reset the ERRCS timeout bit in case it's set */
+ nand |= 1 << RC32434_ERR_WTO;
- if (rc32434_wdt_device.running) {
+ SET_BITS(wdt_reg->errcs, or, nand);
- val = ~RC32434_WTC_EN;
- writel(readl(&wdt_reg->wtc) & val, &wdt_reg->wtc);
+ /* reset WTC timeout bit and enable WDT */
+ nand = 1 << RC32434_WTC_TO;
+ or = 1 << RC32434_WTC_EN;
- val = ~RC32434_ERR_WRE;
- writel(readl(&wdt_reg->errcs) & val, &wdt_reg->errcs);
+ SET_BITS(wdt_reg->wtc, or, nand);
+}
- rc32434_wdt_device.running = 0;
- }
+static void rc32434_wdt_stop(void)
+{
+ /* Disable WDT */
+ SET_BITS(wdt_reg->wtc, 0, 1 << RC32434_WTC_EN);
}
-static void rc32434_wdt_set(int new_timeout)
+static int rc32434_wdt_set(int new_timeout)
{
- u32 cmp = new_timeout * HZ;
- u32 state, val;
+ int max_to = WTCOMP2SEC((u32)-1);
+ if (new_timeout < 0 || new_timeout > max_to) {
+ printk(KERN_ERR KBUILD_MODNAME
+ ": timeout value must be between 0 and %d",
+ max_to);
+ return -EINVAL;
+ }
timeout = new_timeout;
- /*
- * store and disable WTC
- */
- state = (u32)(readl(&wdt_reg->wtc) & RC32434_WTC_EN);
- val = ~RC32434_WTC_EN;
- writel(readl(&wdt_reg->wtc) & val, &wdt_reg->wtc);
-
- writel(0, &wdt_reg->wtcount);
- writel(cmp, &wdt_reg->wtcompare);
-
- /*
- * restore WTC
- */
-
- writel(readl(&wdt_reg->wtc) | state, &wdt_reg);
-}
+ writel(SEC2WTCOMP(timeout), &wdt_reg->wtcompare);
-static void rc32434_wdt_reset(void)
-{
- ticks = rc32434_wdt_device.default_ticks;
+ return 0;
}
-static void rc32434_wdt_update(unsigned long unused)
+static void rc32434_wdt_ping(void)
{
- if (rc32434_wdt_device.running)
- ticks--;
-
writel(0, &wdt_reg->wtcount);
-
- if (rc32434_wdt_device.queue && ticks)
- mod_timer(&rc32434_wdt_device.timer,
- jiffies + RC32434_WDT_INTERVAL);
- else
- complete(&rc32434_wdt_device.stop);
}
static int rc32434_wdt_open(struct inode *inode, struct file *file)
@@ -142,19 +127,23 @@ static int rc32434_wdt_open(struct inode *inode, struct file *file)
if (nowayout)
__module_get(THIS_MODULE);
+ rc32434_wdt_start();
+ rc32434_wdt_ping();
+
return nonseekable_open(inode, file);
}
static int rc32434_wdt_release(struct inode *inode, struct file *file)
{
- if (expect_close && nowayout == 0) {
+ if (expect_close == 42) {
rc32434_wdt_stop();
printk(KERN_INFO KBUILD_MODNAME ": disabling watchdog timer\n");
module_put(THIS_MODULE);
- } else
+ } else {
printk(KERN_CRIT KBUILD_MODNAME
": device closed unexpectedly. WDT will not stop !\n");
-
+ rc32434_wdt_ping();
+ }
clear_bit(0, &rc32434_wdt_device.inuse);
return 0;
}
@@ -174,10 +163,10 @@ static ssize_t rc32434_wdt_write(struct file *file, const char *data,
if (get_user(c, data + i))
return -EFAULT;
if (c == 'V')
- expect_close = 1;
+ expect_close = 42;
}
}
- rc32434_wdt_update(0);
+ rc32434_wdt_ping();
return len;
}
return 0;
@@ -197,11 +186,11 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
};
switch (cmd) {
case WDIOC_KEEPALIVE:
- rc32434_wdt_reset();
+ rc32434_wdt_ping();
break;
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
- value = readl(&wdt_reg->wtcount);
+ value = 0;
if (copy_to_user(argp, &value, sizeof(int)))
return -EFAULT;
break;
@@ -218,6 +207,7 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
break;
case WDIOS_DISABLECARD:
rc32434_wdt_stop();
+ break;
default:
return -EINVAL;
}
@@ -225,11 +215,9 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
case WDIOC_SETTIMEOUT:
if (copy_from_user(&new_timeout, argp, sizeof(int)))
return -EFAULT;
- if (new_timeout < 1)
+ if (rc32434_wdt_set(new_timeout))
return -EINVAL;
- if (new_timeout > MAX_TIMEOUT)
- return -EINVAL;
- rc32434_wdt_set(new_timeout);
+ /* Fall through */
case WDIOC_GETTIMEOUT:
return copy_to_user(argp, &timeout, sizeof(int));
default:
@@ -254,15 +242,15 @@ static struct miscdevice rc32434_wdt_miscdev = {
.fops = &rc32434_wdt_fops,
};
-static char banner[] = KERN_INFO KBUILD_MODNAME
+static char banner[] __devinitdata = KERN_INFO KBUILD_MODNAME
": Watchdog Timer version " VERSION ", timer margin: %d sec\n";
-static int rc32434_wdt_probe(struct platform_device *pdev)
+static int __devinit rc32434_wdt_probe(struct platform_device *pdev)
{
int ret;
struct resource *r;
- r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rb500_wdt_res");
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rb532_wdt_res");
if (!r) {
printk(KERN_ERR KBUILD_MODNAME
"failed to retrieve resources\n");
@@ -277,24 +265,12 @@ static int rc32434_wdt_probe(struct platform_device *pdev)
}
ret = misc_register(&rc32434_wdt_miscdev);
-
if (ret < 0) {
printk(KERN_ERR KBUILD_MODNAME
"failed to register watchdog device\n");
goto unmap;
}
- init_completion(&rc32434_wdt_device.stop);
- rc32434_wdt_device.queue = 0;
-
- clear_bit(0, &rc32434_wdt_device.inuse);
-
- setup_timer(&rc32434_wdt_device.timer, rc32434_wdt_update, 0L);
-
- rc32434_wdt_device.default_ticks = ticks;
-
- rc32434_wdt_start();
-
printk(banner, timeout);
return 0;
@@ -304,23 +280,17 @@ unmap:
return ret;
}
-static int rc32434_wdt_remove(struct platform_device *pdev)
+static int __devexit rc32434_wdt_remove(struct platform_device *pdev)
{
- if (rc32434_wdt_device.queue) {
- rc32434_wdt_device.queue = 0;
- wait_for_completion(&rc32434_wdt_device.stop);
- }
misc_deregister(&rc32434_wdt_miscdev);
-
iounmap(wdt_reg);
-
return 0;
}
static struct platform_driver rc32434_wdt = {
.probe = rc32434_wdt_probe,
- .remove = rc32434_wdt_remove,
- .driver = {
+ .remove = __devexit_p(rc32434_wdt_remove),
+ .driver = {
.name = "rc32434_wdt",
}
};
diff --git a/fs/ext4/ialloc.c b/fs/ext4/ialloc.c
index f18a919be70..627f8c3337a 100644
--- a/fs/ext4/ialloc.c
+++ b/fs/ext4/ialloc.c
@@ -188,7 +188,7 @@ void ext4_free_inode(handle_t *handle, struct inode *inode)
struct ext4_group_desc *gdp;
struct ext4_super_block *es;
struct ext4_sb_info *sbi;
- int fatal = 0, err, count;
+ int fatal = 0, err, count, cleared;
ext4_group_t flex_group;
if (atomic_read(&inode->i_count) > 1) {
@@ -248,8 +248,10 @@ void ext4_free_inode(handle_t *handle, struct inode *inode)
goto error_return;
/* Ok, now we can actually update the inode bitmaps.. */
- if (!ext4_clear_bit_atomic(sb_bgl_lock(sbi, block_group),
- bit, bitmap_bh->b_data))
+ spin_lock(sb_bgl_lock(sbi, block_group));
+ cleared = ext4_clear_bit(bit, bitmap_bh->b_data);
+ spin_unlock(sb_bgl_lock(sbi, block_group));
+ if (!cleared)
ext4_error(sb, "ext4_free_inode",
"bit already cleared for inode %lu", ino);
else {
diff --git a/fs/squashfs/block.c b/fs/squashfs/block.c
index c837dfc2b3c..321728f48f2 100644
--- a/fs/squashfs/block.c
+++ b/fs/squashfs/block.c
@@ -80,7 +80,7 @@ static struct buffer_head *get_block_length(struct super_block *sb,
* generated a larger block - this does occasionally happen with zlib).
*/
int squashfs_read_data(struct super_block *sb, void **buffer, u64 index,
- int length, u64 *next_index, int srclength)
+ int length, u64 *next_index, int srclength, int pages)
{
struct squashfs_sb_info *msblk = sb->s_fs_info;
struct buffer_head **bh;
@@ -185,6 +185,14 @@ int squashfs_read_data(struct super_block *sb, void **buffer, u64 index,
}
if (msblk->stream.avail_out == 0) {
+ if (page == pages) {
+ ERROR("zlib_inflate tried to "
+ "decompress too much data, "
+ "expected %d bytes. Zlib "
+ "data probably corrupt\n",
+ srclength);
+ goto release_mutex;
+ }
msblk->stream.next_out = buffer[page++];
msblk->stream.avail_out = PAGE_CACHE_SIZE;
}
@@ -268,7 +276,8 @@ block_release:
put_bh(bh[k]);
read_failure:
- ERROR("sb_bread failed reading block 0x%llx\n", cur_index);
+ ERROR("squashfs_read_data failed to read block 0x%llx\n",
+ (unsigned long long) index);
kfree(bh);
return -EIO;
}
diff --git a/fs/squashfs/cache.c b/fs/squashfs/cache.c
index f29eda16d25..1c4739e33af 100644
--- a/fs/squashfs/cache.c
+++ b/fs/squashfs/cache.c
@@ -119,7 +119,7 @@ struct squashfs_cache_entry *squashfs_cache_get(struct super_block *sb,
entry->length = squashfs_read_data(sb, entry->data,
block, length, &entry->next_index,
- cache->block_size);
+ cache->block_size, cache->pages);
spin_lock(&cache->lock);
@@ -406,7 +406,7 @@ int squashfs_read_table(struct super_block *sb, void *buffer, u64 block,
for (i = 0; i < pages; i++, buffer += PAGE_CACHE_SIZE)
data[i] = buffer;
res = squashfs_read_data(sb, data, block, length |
- SQUASHFS_COMPRESSED_BIT_BLOCK, NULL, length);
+ SQUASHFS_COMPRESSED_BIT_BLOCK, NULL, length, pages);
kfree(data);
return res;
}
diff --git a/fs/squashfs/inode.c b/fs/squashfs/inode.c
index 7a63398bb85..9101dbde39e 100644
--- a/fs/squashfs/inode.c
+++ b/fs/squashfs/inode.c
@@ -133,7 +133,8 @@ int squashfs_read_inode(struct inode *inode, long long ino)
type = le16_to_cpu(sqshb_ino->inode_type);
switch (type) {
case SQUASHFS_REG_TYPE: {
- unsigned int frag_offset, frag_size, frag;
+ unsigned int frag_offset, frag;
+ int frag_size;
u64 frag_blk;
struct squashfs_reg_inode *sqsh_ino = &squashfs_ino.reg;
@@ -175,7 +176,8 @@ int squashfs_read_inode(struct inode *inode, long long ino)
break;
}
case SQUASHFS_LREG_TYPE: {
- unsigned int frag_offset, frag_size, frag;
+ unsigned int frag_offset, frag;
+ int frag_size;
u64 frag_blk;
struct squashfs_lreg_inode *sqsh_ino = &squashfs_ino.lreg;
diff --git a/fs/squashfs/squashfs.h b/fs/squashfs/squashfs.h
index 6b2515d027d..0e9feb6adf7 100644
--- a/fs/squashfs/squashfs.h
+++ b/fs/squashfs/squashfs.h
@@ -34,7 +34,7 @@ static inline struct squashfs_inode_info *squashfs_i(struct inode *inode)
/* block.c */
extern int squashfs_read_data(struct super_block *, void **, u64, int, u64 *,
- int);
+ int, int);
/* cache.c */
extern struct squashfs_cache *squashfs_cache_init(char *, int, int);
diff --git a/fs/squashfs/super.c b/fs/squashfs/super.c
index 071df5b5b49..681ec0d8379 100644
--- a/fs/squashfs/super.c
+++ b/fs/squashfs/super.c
@@ -389,7 +389,7 @@ static int __init init_squashfs_fs(void)
return err;
}
- printk(KERN_INFO "squashfs: version 4.0 (2009/01/03) "
+ printk(KERN_INFO "squashfs: version 4.0 (2009/01/31) "
"Phillip Lougher\n");
return 0;
diff --git a/include/asm-generic/vmlinux.lds.h b/include/asm-generic/vmlinux.lds.h
index 89997dfdf3d..0e0f39be6c8 100644
--- a/include/asm-generic/vmlinux.lds.h
+++ b/include/asm-generic/vmlinux.lds.h
@@ -98,6 +98,7 @@
VMLINUX_SYMBOL(__stop___tracepoints) = .; \
LIKELY_PROFILE() \
BRANCH_PROFILE() \
+ TRACE_PRINTKS() \
FTRACE_EVENTS()
#define RO_DATA(align) \
@@ -108,7 +109,6 @@
*(__vermagic) /* Kernel version magic */ \
*(__markers_strings) /* Markers: strings */ \
*(__tracepoints_strings)/* Tracepoints: strings */ \
- TRACE_PRINTKS() \
} \
\
.rodata1 : AT(ADDR(.rodata1) - LOAD_OFFSET) { \
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 08a86d5cdf1..9a061accd8b 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -89,6 +89,8 @@ enum {
ATA_ID_DLF = 128,
ATA_ID_CSFO = 129,
ATA_ID_CFA_POWER = 160,
+ ATA_ID_CFA_KEY_MGMT = 162,
+ ATA_ID_CFA_MODES = 163,
ATA_ID_ROT_SPEED = 217,
ATA_ID_PIO4 = (1 << 1),
diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h
index f0413845f20..1956c8d46d3 100644
--- a/include/linux/dmaengine.h
+++ b/include/linux/dmaengine.h
@@ -97,7 +97,6 @@ typedef struct { DECLARE_BITMAP(bits, DMA_TX_TYPE_END); } dma_cap_mask_t;
/**
* struct dma_chan_percpu - the per-CPU part of struct dma_chan
- * @refcount: local_t used for open-coded "bigref" counting
* @memcpy_count: transaction counter
* @bytes_transferred: byte counter
*/
@@ -114,9 +113,6 @@ struct dma_chan_percpu {
* @cookie: last cookie value returned to client
* @chan_id: channel ID for sysfs
* @dev: class device for sysfs
- * @refcount: kref, used in "bigref" slow-mode
- * @slow_ref: indicates that the DMA channel is free
- * @rcu: the DMA channel's RCU head
* @device_node: used to add this to the device chan list
* @local: per-cpu pointer to a struct dma_chan_percpu
* @client-count: how many clients are using this channel
@@ -213,8 +209,6 @@ struct dma_async_tx_descriptor {
* @global_node: list_head for global dma_device_list
* @cap_mask: one or more dma_capability flags
* @max_xor: maximum number of xor sources, 0 if no capability
- * @refcount: reference count
- * @done: IO completion struct
* @dev_id: unique device ID
* @dev: struct device reference for dma mapping api
* @device_alloc_chan_resources: allocate resources and return the
@@ -227,6 +221,7 @@ struct dma_async_tx_descriptor {
* @device_prep_dma_interrupt: prepares an end of chain interrupt operation
* @device_prep_slave_sg: prepares a slave dma operation
* @device_terminate_all: terminate all pending operations
+ * @device_is_tx_complete: poll for transaction completion
* @device_issue_pending: push pending transactions to hardware
*/
struct dma_device {
diff --git a/include/linux/hdreg.h b/include/linux/hdreg.h
index c37e9241fae..ed21bd3dbd2 100644
--- a/include/linux/hdreg.h
+++ b/include/linux/hdreg.h
@@ -511,7 +511,6 @@ struct hd_driveid {
unsigned short words69_70[2]; /* reserved words 69-70
* future command overlap and queuing
*/
- /* HDIO_GET_IDENTITY currently returns only words 0 through 70 */
unsigned short words71_74[4]; /* reserved words 71-74
* for IDENTIFY PACKET DEVICE command
*/
diff --git a/include/linux/ide.h b/include/linux/ide.h
index fe235b65207..e0cedfe9fad 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -866,6 +866,7 @@ struct ide_host {
unsigned int n_ports;
struct device *dev[2];
unsigned int (*init_chipset)(struct pci_dev *);
+ irq_handler_t irq_handler;
unsigned long host_flags;
void *host_priv;
ide_hwif_t *cur_port; /* for hosts requiring serialization */
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index 4e726b9a71e..7742798c920 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -454,7 +454,10 @@ do { \
do { \
static const char *trace_printk_fmt \
__attribute__((section("__trace_printk_fmt"))); \
- trace_printk_fmt = fmt; \
+ \
+ if (!trace_printk_fmt) \
+ trace_printk_fmt = fmt; \
+ \
__trace_printk_check_format(fmt, ##args); \
__trace_printk(_THIS_IP_, trace_printk_fmt, ##args); \
} while (0)
@@ -467,7 +470,10 @@ __trace_printk(unsigned long ip, const char *fmt, ...)
do { \
static const char *trace_printk_fmt \
__attribute__((section("__trace_printk_fmt"))); \
- trace_printk_fmt = fmt; \
+ \
+ if (!trace_printk_fmt) \
+ trace_printk_fmt = fmt; \
+ \
__ftrace_vprintk(_THIS_IP_, trace_printk_fmt, vargs); \
} while (0)
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 5d87bc09a1f..dc18b87ed72 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -275,7 +275,7 @@ enum {
* advised to wait only for the following duration before
* doing SRST.
*/
- ATA_TMOUT_PMP_SRST_WAIT = 1000,
+ ATA_TMOUT_PMP_SRST_WAIT = 5000,
/* ATA bus states */
BUS_UNKNOWN = 0,
@@ -530,6 +530,7 @@ struct ata_queued_cmd {
unsigned long flags; /* ATA_QCFLAG_xxx */
unsigned int tag;
unsigned int n_elem;
+ unsigned int orig_n_elem;
int dma_dir;
@@ -750,7 +751,8 @@ struct ata_port {
acpi_handle acpi_handle;
struct ata_acpi_gtm __acpi_init_gtm; /* use ata_acpi_init_gtm() */
#endif
- u8 sector_buf[ATA_SECT_SIZE]; /* owned by EH */
+ /* owned by EH */
+ u8 sector_buf[ATA_SECT_SIZE] ____cacheline_aligned;
};
/* The following initializer overrides a method to NULL whether one of
diff --git a/include/linux/serio.h b/include/linux/serio.h
index 1bcb357a01a..e0417e4d3f1 100644
--- a/include/linux/serio.h
+++ b/include/linux/serio.h
@@ -212,7 +212,7 @@ static inline void serio_unpin_driver(struct serio *serio)
#define SERIO_FUJITSU 0x35
#define SERIO_ZHENHUA 0x36
#define SERIO_INEXIO 0x37
-#define SERIO_TOUCHIT213 0x37
+#define SERIO_TOUCHIT213 0x38
#define SERIO_W8001 0x39
#endif
diff --git a/kernel/softirq.c b/kernel/softirq.c
index 98dd68eea9e..bbf6d6496f0 100644
--- a/kernel/softirq.c
+++ b/kernel/softirq.c
@@ -637,6 +637,7 @@ static int ksoftirqd(void * __bind_cpu)
preempt_enable_no_resched();
cond_resched();
preempt_disable();
+ rcu_qsctr_inc((long)__bind_cpu);
}
preempt_enable();
set_current_state(TASK_INTERRUPTIBLE);
diff --git a/security/smack/smack_lsm.c b/security/smack/smack_lsm.c
index 0278bc08304..e7ded1326b0 100644
--- a/security/smack/smack_lsm.c
+++ b/security/smack/smack_lsm.c
@@ -1498,58 +1498,31 @@ static int smack_socket_post_create(struct socket *sock, int family,
* looks for host based access restrictions
*
* This version will only be appropriate for really small
- * sets of single label hosts. Because of the masking
- * it cannot shortcut out on the first match. There are
- * numerious ways to address the problem, but none of them
- * have been applied here.
+ * sets of single label hosts.
*
* Returns the label of the far end or NULL if it's not special.
*/
static char *smack_host_label(struct sockaddr_in *sip)
{
struct smk_netlbladdr *snp;
- char *bestlabel = NULL;
struct in_addr *siap = &sip->sin_addr;
- struct in_addr *liap;
- struct in_addr *miap;
- struct in_addr bestmask;
if (siap->s_addr == 0)
return NULL;
- bestmask.s_addr = 0;
-
for (snp = smack_netlbladdrs; snp != NULL; snp = snp->smk_next) {
- liap = &snp->smk_host.sin_addr;
- miap = &snp->smk_mask;
- /*
- * If the addresses match after applying the list entry mask
- * the entry matches the address. If it doesn't move along to
- * the next entry.
- */
- if ((liap->s_addr & miap->s_addr) !=
- (siap->s_addr & miap->s_addr))
- continue;
/*
- * If the list entry mask identifies a single address
- * it can't get any more specific.
+ * we break after finding the first match because
+ * the list is sorted from longest to shortest mask
+ * so we have found the most specific match
*/
- if (miap->s_addr == 0xffffffff)
+ if ((&snp->smk_host.sin_addr)->s_addr ==
+ (siap->s_addr & (&snp->smk_mask)->s_addr)) {
return snp->smk_label;
- /*
- * If the list entry mask is less specific than the best
- * already found this entry is uninteresting.
- */
- if ((miap->s_addr | bestmask.s_addr) == bestmask.s_addr)
- continue;
- /*
- * This is better than any entry found so far.
- */
- bestmask.s_addr = miap->s_addr;
- bestlabel = snp->smk_label;
+ }
}
- return bestlabel;
+ return NULL;
}
/**
diff --git a/security/smack/smackfs.c b/security/smack/smackfs.c
index 8e42800878f..51f0efc50da 100644
--- a/security/smack/smackfs.c
+++ b/security/smack/smackfs.c
@@ -650,10 +650,6 @@ static void *netlbladdr_seq_next(struct seq_file *s, void *v, loff_t *pos)
return skp;
}
-/*
-#define BEMASK 0x80000000
-*/
-#define BEMASK 0x00000001
#define BEBITS (sizeof(__be32) * 8)
/*
@@ -663,12 +659,10 @@ static int netlbladdr_seq_show(struct seq_file *s, void *v)
{
struct smk_netlbladdr *skp = (struct smk_netlbladdr *) v;
unsigned char *hp = (char *) &skp->smk_host.sin_addr.s_addr;
- __be32 bebits;
- int maskn = 0;
+ int maskn;
+ u32 temp_mask = be32_to_cpu(skp->smk_mask.s_addr);
- for (bebits = BEMASK; bebits != 0; maskn++, bebits <<= 1)
- if ((skp->smk_mask.s_addr & bebits) == 0)
- break;
+ for (maskn = 0; temp_mask; temp_mask <<= 1, maskn++);
seq_printf(s, "%u.%u.%u.%u/%d %s\n",
hp[0], hp[1], hp[2], hp[3], maskn, skp->smk_label);
@@ -702,6 +696,42 @@ static int smk_open_netlbladdr(struct inode *inode, struct file *file)
}
/**
+ * smk_netlbladdr_insert
+ * @new : netlabel to insert
+ *
+ * This helper insert netlabel in the smack_netlbladdrs list
+ * sorted by netmask length (longest to smallest)
+ */
+static void smk_netlbladdr_insert(struct smk_netlbladdr *new)
+{
+ struct smk_netlbladdr *m;
+
+ if (smack_netlbladdrs == NULL) {
+ smack_netlbladdrs = new;
+ return;
+ }
+
+ /* the comparison '>' is a bit hacky, but works */
+ if (new->smk_mask.s_addr > smack_netlbladdrs->smk_mask.s_addr) {
+ new->smk_next = smack_netlbladdrs;
+ smack_netlbladdrs = new;
+ return;
+ }
+ for (m = smack_netlbladdrs; m != NULL; m = m->smk_next) {
+ if (m->smk_next == NULL) {
+ m->smk_next = new;
+ return;
+ }
+ if (new->smk_mask.s_addr > m->smk_next->smk_mask.s_addr) {
+ new->smk_next = m->smk_next;
+ m->smk_next = new;
+ return;
+ }
+ }
+}
+
+
+/**
* smk_write_netlbladdr - write() for /smack/netlabel
* @filp: file pointer, not actually used
* @buf: where to get the data from
@@ -724,8 +754,9 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
struct netlbl_audit audit_info;
struct in_addr mask;
unsigned int m;
- __be32 bebits = BEMASK;
+ u32 mask_bits = (1<<31);
__be32 nsa;
+ u32 temp_mask;
/*
* Must have privilege.
@@ -761,10 +792,13 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
if (sp == NULL)
return -EINVAL;
- for (mask.s_addr = 0; m > 0; m--) {
- mask.s_addr |= bebits;
- bebits <<= 1;
+ for (temp_mask = 0; m > 0; m--) {
+ temp_mask |= mask_bits;
+ mask_bits >>= 1;
}
+ mask.s_addr = cpu_to_be32(temp_mask);
+
+ newname.sin_addr.s_addr &= mask.s_addr;
/*
* Only allow one writer at a time. Writes should be
* quite rare and small in any case.
@@ -772,6 +806,7 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
mutex_lock(&smk_netlbladdr_lock);
nsa = newname.sin_addr.s_addr;
+ /* try to find if the prefix is already in the list */
for (skp = smack_netlbladdrs; skp != NULL; skp = skp->smk_next)
if (skp->smk_host.sin_addr.s_addr == nsa &&
skp->smk_mask.s_addr == mask.s_addr)
@@ -787,9 +822,8 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
rc = 0;
skp->smk_host.sin_addr.s_addr = newname.sin_addr.s_addr;
skp->smk_mask.s_addr = mask.s_addr;
- skp->smk_next = smack_netlbladdrs;
skp->smk_label = sp;
- smack_netlbladdrs = skp;
+ smk_netlbladdr_insert(skp);
}
} else {
rc = netlbl_cfg_unlbl_static_del(&init_net, NULL,
diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 3bc427645da..6094344fb22 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -1207,7 +1207,7 @@ static const char *slave_vols[] = {
"LFE Playback Volume",
"Side Playback Volume",
"Headphone Playback Volume",
- "Headphone Playback Volume",
+ "Headphone2 Playback Volume",
"Speaker Playback Volume",
"External Speaker Playback Volume",
"Speaker2 Playback Volume",
@@ -1221,7 +1221,7 @@ static const char *slave_sws[] = {
"LFE Playback Switch",
"Side Playback Switch",
"Headphone Playback Switch",
- "Headphone Playback Switch",
+ "Headphone2 Playback Switch",
"Speaker Playback Switch",
"External Speaker Playback Switch",
"Speaker2 Playback Switch",
@@ -3516,6 +3516,7 @@ static int stac92xx_parse_auto_config(struct hda_codec *codec, hda_nid_t dig_out
if (! spec->autocfg.line_outs)
return 0; /* can't find valid pin config */
+#if 0 /* FIXME: temporarily disabled */
/* If we have no real line-out pin and multiple hp-outs, HPs should
* be set up as multi-channel outputs.
*/
@@ -3535,6 +3536,7 @@ static int stac92xx_parse_auto_config(struct hda_codec *codec, hda_nid_t dig_out
spec->autocfg.line_out_type = AUTO_PIN_HP_OUT;
spec->autocfg.hp_outs = 0;
}
+#endif /* FIXME: temporarily disabled */
if (spec->autocfg.mono_out_pin) {
int dir = get_wcaps(codec, spec->autocfg.mono_out_pin) &
(AC_WCAP_OUT_AMP | AC_WCAP_IN_AMP);